Fire Fighting Robot, Fire Fighting Robotic Car, New Electronics Project #science #shorts
Summary
TLDRThis instructional video script guides viewers through assembling a DIY project involving a playboard, DC motor, wheels, and a servo motor. It details the process of connecting these components with glue and screws, integrating sensors, a motor driver, and a battery holder. The script also covers programming the project using an OTG cable and uploading code to an Arduino board. Finally, it demonstrates connecting a water pump and testing the system's functionality, including water flow control and directional movement.
Takeaways
- 😀 The project involves building a device using a play board, a DC motor, and glue to fix the components.
- 🔧 A wooden piece and a round rod are attached to the play board using screws to connect the wheels.
- 🔌 The project requires connecting the wheels to two motors in a specific manner.
- 💻 The device is programmed using an OTG cable connected to a laptop, and the program is uploaded to the device.
- 🔩 Additional components like an L298 motor driver, three flame sensors, and a battery holder are fixed to the play board using screws.
- 🔋 A 5-volt relay and a small PC mode with a Mel header are connected, and the battery holder's positive wire is connected to the first train of the motor driver.
- 🔌 A switch is connected to the motor driver, and a dumper wire is connected to the motor driver's middle point for power supply.
- 💧 A DC water pump is connected to the motor driver, and a water level pipe is used to control the water flow.
- 🎚️ The device includes a servo motor that can be controlled to move left, right, or forward, and it also controls the water flow.
- 🔧 The final assembly involves securing all components with screws and placing them inside a plastic box for stability and protection.
Q & A
What is the main project being discussed in the script?
-The script discusses a project involving the assembly of a device using a play board, a DC motor, and other components like sensors and a motor driver.
What are the primary components used to build the project?
-The primary components include a play board, a DC motor, a wooden piece, wheels, screws, a motor driver, sensors, a battery holder, and a 5-volt relay.
How is the DC motor connected to the play board?
-The DC motor is connected to the play board by gluing it in place using glue.
What is the purpose of the wooden piece and the round wheel in the project?
-The wooden piece and the round wheel are used to connect and support the structure, likely for stability and to facilitate movement.
How is the program uploaded to the device?
-The program is uploaded to the device by connecting it to a laptop via an OTG cable and then opening and uploading the program through the connected laptop.
What is the role of the L298 motor driver in the project?
-The L298 motor driver is used to control the motors, likely to manage the speed and direction of the wheels.
How many sensors are used in the project and what are they used for?
-Three sensors are used in the project, likely for detecting obstacles or for navigation purposes.
What is the purpose of the battery holder in the project?
-The battery holder is used to power the device, providing the necessary voltage for the components to function.
How are the connections made between the components?
-The connections between the components are made using screws, wires, and soldering, ensuring a stable and secure electrical connection.
What is the function of the 5-volt relay in the project?
-The 5-volt relay is used to control the flow of power to certain components, likely for switching on and off devices or circuits.
How is the water pump connected and what is its purpose?
-The water pump is connected to the motor driver and is used to pump water, possibly as part of a demonstration or testing the functionality of the device.
Outlines
🔧 Building the Project
The paragraph describes the process of assembling a DIY project involving a playboard, a DC motor, and wheels. The playboard and motor are glued together, and a piece of wood is attached to serve as a round base. Wheels are then connected to the motors. The project is programmed using an OTG cable connected to a laptop. The program is uploaded to the device, and screws are used to secure the components to the playboard. An L298 motor driver is also fixed to the playboard. Three flame sensors are connected and fixed in place. A battery holder is attached, and a servo motor is fixed. A 5-volt relay is also connected to the playboard. The connections involve a series of wires being attached to various components, including a switch, dumper wire, and motor driver. The process concludes with the motor connections being made, and the sensors' data and ground pins being connected to the microcontroller.
🚂 Connecting the Circuit
This paragraph details the continuation of the project assembly, focusing on connecting the circuitry. It involves connecting the relay to the motor driver and setting up the connections for the relay in the series with 5 volts and ground. The connections are extended to include the inputs and outputs of the motor driver, with wires being connected to the audio pins of the microcontroller. The motor connections are made to the output pins of the motor driver. The paragraph also describes the process of securing all the connections with screws and playboard. Additional connections are made for the motor driver's ground and 12-volt pin. A plastic box is used to encase the setup, and a water level pipe is connected to facilitate the flow of water. The water pump is connected to the motor driver, and the battery is connected to power the system. The water pump's operation is tested by changing the relay connections to reverse the flow direction.
💧 Testing the Water Flow System
The final paragraph outlines the testing phase of the project. It involves filling a plastic box with water and observing the water flow through the pipe. The water pump is tested for its automatic flow capabilities. The paragraph describes making adjustments to the setup by cutting a small piece of the can to allow the water to flow more effectively. The testing includes moving the setup in different directions to observe the water flow and the operation of the water pump. The paragraph concludes with an invitation for viewers to share their thoughts on the project in the comments section.
Mindmap
Keywords
💡Playboard
💡DC Motor
💡Glue
💡Wheel
💡L298 Motor Driver
💡Sensor
💡Battery Holder
💡Servo Motor
💡Water Pump
💡Relay
💡PC Mode
Highlights
Introduction to building a project with a complete explanation in the video.
Using a small play board and a DC motor to build the project.
Attaching the motor and play board using glue.
Connecting wheels to the motor with the help of screws.
Fixing a piece of wood and a round wheel to the play board.
Connecting the wheels to the two motors.
Uploading the program to the project via a laptop.
Connecting the project to the laptop using an OTG cable.
Programming the board using Arduino software.
Fixing the Arduino board to the play board with screws.
Attaching an L298 motor driver and connecting it to the play board.
Using three flame sensors and connecting them to the play board.
Fixing a battery holder to the play board.
Connecting a servo motor to the side of the play board.
Connecting a 5-volt relay to the play board using glue.
Connecting a small PC mode with male header pins.
Connecting the battery holder's positive wire to the motor driver.
Connecting a switch to the motor driver for power control.
Connecting a 5-volt power supply to the motor driver.
Connecting the three sensors' data pins to the Arduino.
Connecting the servo motor to the relay.
Connecting the relay to the water pump.
Testing the water pump and its automatic flow control.
Filling the plastic box with water for testing the project.
Final testing of the project's movement and water flow control.
Transcripts
[संगीत]
हेलो गैस आप देख रहे हो
तो आप इस प्रोजेक्ट को कैसे बना सकते हैं
इसका कंप्लीट एक्सप्लेन हमने इस वीडियो
में दिखाए अगर आप इस वीडियो को पूरा देखते
हैं तो आप भी प्रोजेक्ट को आसानी से बना
पाएंगे तो चलिए बिना किसी डेरी के शुरू
करते हैं इसके लिए हम एक छोटा सा प्लाई
बोर्ड लेंगे और तू डीसी मोटर लेंगे और
ग्लू की मदद से इसी प्लाई बोर्ड में
इन्हें चिपका देंगे इस तरह से चिपकाएंगे
की हम इनमें व्हील कनेक्ट करेंगे और फिर
इसके बाद हम एक लकड़ी का टुकड़ा भी यही पे
चिपका देंगे और एक राउंड लेंगे ये और इसे
भी यही पे कनेक्ट कर देंगे स्क्रू की मदद
से
और फिर इसके बाद हम इन में व्हील्स को
कनेक्ट कर देंगे इन दोनों मोटर में इस तरह
से
[संगीत]
अब इसके बाद लेंगे बट उससे पहले हम इसमें
प्रोग्राम को अपलोड करेंगे तो इसके लिए हम
इसे
ओटीजी केवल के थ्रू अपने लैपटॉप से कनेक्ट
कर लेंगे
तो हमने इसे अपने लैपटॉप से कनेक्ट कर
लिया है अब हम उसे प्रोग्राम को ओपन
करेंगे जिससे हमें इसमें अपलोड करना है और
फिर इसके बाद इसमें हम ऑर्डिन बोर्ड और
सिलेक्ट करने के बाद इस कैसे में जाकर इसे
अपलोड कर देते हैं तो उसे टाइम में ये
प्रोग्राम अपलोड हो जाएगा दान अपलोडिंग
दिखा रहा है अब हम 2 स्क्रू की मदद से इसे
इसी प्लाई बोर्ड में फिक्स कर देंगे यानी
राइनो को फिक्स कर देंगे
अब इसके बाद हम l298 और मोटर ड्राइवर
लेंगे और इसे भी हम तू स्क्रू की मदद से
इसी प्लाईवुड में फिक्स कर देंगे और फिर
इसके बाद हम थ्री फ्लेम सेंसर लेंगे यानी
फाइव सेंसर लेंगे और फिर इन्हें भी हम इसी
प्लाई बोर्ड में आगे की साइड कनेक्ट कर
देंगे और इनमें भी स्क्रू की मदद से फिक्स
कर देंगे
तो हमने तीनों फिल्म सेंसर को फिक्स कर
दिया है अब इसके बाद हम एक बैटरी होल्डर
लेंगे तू सेल वाले बैटरी होल्डर है इसे भी
हम इसी प्लाई बोर्ड में फिक्स कर देंगे और
फिर इसके बाद हम एक सर्वो मोटर लेंगे और
इसे भी हम आगे की साइड इस तरह से फिक्स कर
देंगे ग्लूसी में से अब इसके बाद हम एक 5
वॉल्ट रिलेटेड लेंगे और इसे भी हम इसी
प्लाई बोर्ड में फिक्स करेंगे ब्लू की मदद
से अब इसके बाद हम एक पीसी मोड लेंगे छोटा
सा और इसमें हम मेल हेडर पी को इस तरह से
कनेक्ट कर दिया है एक साइड हम ग्राउंड
बनाएंगे और एक साइड बीसीजी तो हम एक साथ
जॉइन कर दिया है यानी इसमें सोल्डरिंग कर
दिए हैं तो बीसी और ग्राउंड पे मिल गए हैं
और इसे भी हम ग्लेज में 10 से इसी प्लाई
बोर्ड में चिपका देंगे अब इसके बाद हम
बैटरी होल्डर के यानी पॉजिटिव वायर को हम
फर्स्ट मोटर ड्राइवर की फर्स्ट ट्रेन से
कनेक्ट कर देंगे यानी 12 वॉल्ट वाली पी से
कनेक्ट और ग्राउंड में हम पहले एक स्विच
को कनेक्ट करेंगे और फिर इसके बाद हम
स्विच के दूसरे पॉइंट पर एक डंपर वायर को
कनेक्ट करके मोटर ड्राइवर की मिडिल पर
यानी ग्राउंड पी में कनेक्ट कर देंगे इस
तरह से हमारे मोटर ड्राइवर में पावर ऑन हो
जाएगी सेल के थ्रू अब इसके बाद हम क्या
करेंगे तू डंपर वायर लेंगे हम मोटर
ड्राइवर में एक फाइव बोल्ट पी होती है और
ग्राउंड तो फाइव बोल्ट पेन थर्ड वाली पी
है तो उसमें एक डंपर वायर को कनेक्ट
करेंगे और मिडिल में हम एक ब्लैक जंप
प्रोवाइड को कनेक्ट करेंगे अब इस तरह से
हमें 5 वॉल्ट डॉ मिल जाएगी और फिर हम जो
हमने हेडर पी लगे थी बीसी और ब्राउन की तो
उनमें हम पर वायर को कनेक्ट करेंगे फाइव
बोल्ट वाली पी को हम बीसी में और गाउन
वाले पी को ग्राउंड में तो इस तरह से
व्हाइटफील्ड
ग्राउंड है तो इस तरह से हमें काफी सारे
पॉइंट मिल जाएंगे
इस सीरीज में कनेक्ट कर देंगे जहां हमने
कनेक्ट किया थे तो इस तरह से इन तीनों में
पावर सप्लाई ऑन हो जाएगी यानी पावर सप्लाई
मिल जाएगी
और फिर हम इस सर्किट के जैसे ही इन सभी
कंपोनेंट के कनेक्शन करेंगे
तो हमने तीनों सेंसर की विशेष्य और
ग्राउंड पी को कनेक्ट कर दिया है अब इसके
बाद हम तीनों सेंसर की डाटा पी के कनेक्शन
करेंगे तो हम मिडिल वाले सेंसर की डाटा पी
का कनेक्शन हम एक नंबर पी से करेंगे और
फिर लेफ्ट साइड वाली डाटा पी का कनेक्शन
नंबर लाइन से कनेक्ट करेंगे और फिर राइट
साइड वाले सेंसर का कनेक्शन
नंबर 10 से कनेक्ट कर देंगे
तो इस तरह से यह डाटा की कनेक्शन भी
कंप्लीट हो जाते हैं अब इसके बाद हम टर्बो
मोटर के कनेक्शन करेंगे तो हम इसके विशेष
कर लेते हैं और इस सीरीज में 5 वॉल्ट और
ग्राउंड की सीरीज में कनेक्ट कर देते हैं
[संगीत]
इसमें हम एग्जांपल को कनेक्ट करके
[संगीत]
और फिर इसके बाद हम
रेलवे में भी कनेक्शन करेंगे तो रिले में
बीसी और ग्राउंड में डंपर वायर को कनेक्ट
करके इस सीरीज के और गांव में भी कनेक्ट
कर देंगे तो इस तरह से रिले में भी पावर
ऑन हो जाएगी
और इससे बीसी और ग्राउंड में कनेक्ट कर
देंगे
कनेक्ट कर देंगे तो इससे ही हमारे ऑर्डिन
में भी पावर सप्लाई ऑन हो जाएगी तो हमें
ज्यादा पावर सोर्स कनेक्ट करने की जरूर
नहीं पड़ेगी अब इसके बाद हम रिले की इनपुट
पी में एक डंपर वायर को कनेक्ट करके
ऑडियंस की पी नंबर सिक्स से कनेक्ट कर
देते हैं और फिर इसके बाद हम फूड डंपर
वायर और लेंगे और हम मोटर ड्राइवर की
इनपुट प्रिंस में कनेक्ट करके ऑडियो 2345
पी में कनेक्ट कर देते हैं और फिर इसके
बाद हम मोटर की कनेक्शन हम मोटर ड्राइवर
की आउटपुट पेन से करेंगे तो इस तरह से हम
इनमें कनेक्ट कर देते हैं अगर आपकी मोटर
राउंड करती है तो आप इनकी इंटर चेंज
कनेक्शन कर सकते हैं और अगर आपका राइट
साइड में ही चला है तो कोई दिक्कत नहीं
[संगीत]
तुम्हारे सारे कनेक्शन कंप्लीट हो गए हैं
अब इसके बाद हम क्या करेंगे 4 स्क्रू
लेंगे और फिर हम इन सभी में कनेक्ट कर
देंगे इस तरह से
आपको वीडियो में दिखे रहा है ऐसे ही आपको
भी कनेक्ट कर देना है और इतने बड़े ही
स्क्रू का उसे करना है आपको भी
तो हमने फोर होल्स कर लिए थे प्लाई बोर्ड
में और इसी तरह से हमने स्क्रू को कनेक्ट
कर दिया है
[संगीत]
अब इसके बाद हम 2 वायर लेंगे और हम मोटर
ड्राइवर की ग्राउंड पी और 12 वॉल्ट पेन
में कनेक्ट कर देंगे
ऑरेंज वायर
को हम ग्राउंड में कनेक्ट कर देंगे अब
उसके बाद हमने जो स्क्रू कनेक्ट किया थे
उसमें हम इस तरह से प्लाईवुड कनेक्ट कर
देंगे और इसे हम इसी में फिक्स कर देंगे
जिससे की यह स्टेबल रहे और फिर हम इसके
बाद प्लास्टिक का बॉक्स लेंगे यह इस तरह
से डिब्बा लेंगे हम एक प्लास्टिक का और
इसे हम ब्लू की मदद से इसी के ऊपर फिक्स
कर देंगे की जिससे की यह नहीं तो हमने
फिक्स कर दिया है अब इसके बाद हम इसका
ढक्कन निकलते हैं और इसके ढक्कन के
ऊपर हम एक मोटर को कनेक्ट करेंगे यह डीसी
वाटर पंप होता है इसको वही कनेक्ट करेंगे
और इसके बाद हम एक वाटर लेवल पाइप लिया है
हमने इसमें कनेक्ट कर देंगे इसको
और फिर इसके बाद हम कुछ साइज से इसको कट
कर लेते हैं और फिर हम इसी ढक्कन में इसको
होल करके बाहर की साइड निकाल लेंगे और फिर
इसके बाद हम एक और होल करेंगे इस वायर को
निकालना के लिए
तो हमारा मोटर जो रहेगा वह अंदर की साइड
रहेगा और फिर हम इसी डिब्बे में इसको रख
देते हैं अब इसके बाद हम सर्वो के ऊपर एक
स्क्रू को कनेक्ट कर देंगे और फिर हम इस
तरह से एक पाइप लेंगे और इसे भी हम ग्लू
की मदद से इसी के ऊपर चिपका देंगे और फिर
इसके बाद हम जो पाइप कनेक्ट किया था वाटर
लेवल पाइप और इसी में से इसको निकाल लेंगे
जिससे की ये जो वाटर फ्लो होगा वो एक सीध
में ही होगा जो सर्वर मोटर लेफ्ट राइट
उसको मूव कर पाएगी अच्छे से और फिर हमने
जो वायर को कनेक्ट किया थे हमने जो मोटर
ड्राइवर से उन्हें हम वाटर पंप से कनेक्ट
करेंगे तो एक वायर को हमने डायरेक्ट वाटर
पंप के एक वायर से कनेक्ट कर दिया है और
दूसरे वायर को हम पहले रिले की आम पी में
कनेक्ट करेंगे इस तरह से हमने आम पी में
कनेक्ट कर दिया है फिर दूसरे वायर को हमने
रिलेटिव में कनेक्ट किया है और वाटर पंप
के दूसरे वायर में कनेक्ट कर दिया है उसके
बाद हम इसमें सेल को कनेक्ट करेंगे
तो हमने इसी बैटरी होल्डर में इस तरह से
सेल को कनेक्ट कर दिया है यह 3.7 वॉल्ट का
एक सेल होता है और फिर इसके बाद हम जैसे
ही पावर ऑन करेंगे तो अभी क्या है ये
अपोजिट क कर रही यानी जो हमारा वाटर पंप
है वो अभी अपोजिट क कर रहा है इसीलिए हम
रिले के कनेक्शन को चेंज करेंगे तो हम आनो
से हटाकर उसे एनसी में कनेक्ट करेंगे यानी
लास्ट से हटाकर फर्स्ट में कनेक्ट कर
देंगे इस तरह से तो हमारा ये वाटर पंप सही
से कम करने लगेगा अब ये हमने पावर को ऑन
किया तो अभी ये सही से कम कर रहा है अब
इसके बाद हम क्या करेंगे इसमें वाटर को
फाइल कर देंगे यानी जो हमारा बॉक्स है ये
प्लास्टिक का बॉक्स जो डिब्बा है इसमें हम
पानी भर देंगे पूरा और फिर इसके बाद हम
इसकी टेस्टिंग करेंगे
तुमने वाटर को भर दिया उसने और फिर पाइप
को वहीं पर लगा देंगे और पाइप जब वाटर
फ्लो होगा तो यह पाइप है ना जाए इसके लिए
हम इसमें इस तरह से तप लगा देंगे अब इसके
बाद हम इसकी टेस्टिंग करेंगे तो हमने
टेस्टिंग की है शब्द इसमें क्या हो रहा है
की वाटर पंप जो है वो ऑटोमेटिक वाटर को
फ्लो कर रहा है तो इसके लिए हम इसमें अर्न
करने के लिए इसे थोड़ा सा कैंची से यहां
पे कट कर देते हैं इस तरह से और फिर इसके
बाद हम इसे फिर से फिक्स कर देते हैं अब
जैसे ही हम इसके सामने आज ले जाते हैं या
लेफ्ट या राइट साइड में आज ले जाते हैं तो
जी साइड में हम आज को ले जाएंगे इस साइड
में ये चलने लगेगा अगर हम लेफ्ट में ले
जाएंगे तो लेफ्ट साइड में अगर राइट में तो
राइट साइड में और अगर हम फॉरवर्ड में ले
जाएंगे तो सीधा चलेगा और ये साथ में ही
वाटर फ्लो करेगा तो आपको ये कॉन्सेप्ट
कैसा लगा हमें कमेंट में जरूर बताएं और
थैंक्स पर वाचिंग
5.0 / 5 (0 votes)