E-BIKE Conversion SW 900 ERROR Code 09 Troubleshooting | DIY Petz
Summary
TLDRこのビデオでは、エラーコード「ゼロナイン」が表示された電動バイクのコントローラーの修理を紹介しています。問題はモーターが非常に重く動くことから始まり、ケーブルのチェック後も問題が解決せず、コントローラー自体に問題があると判断しました。12つのMOSFETを持ち、それぞれをマルチメーターでショートチェックを行い、ショートが検出されたMOSFETを特定しました。ネットショップで必要なMOSFETを購入し、不良のMOSFETを新しいものに交換しました。修理後、エラーは解消され、スロットルが正常に動作することを確認しました。このビデオは、エラーゼロナインを修復するための手順を詳しく解説しており、類似の問題に対処する際に役立つと思われます。
Takeaways
- 🚲 エレクトリックバイクにエラーコード09が出てコントローラーに問題があると判明しました。
- 🔍 エラーが表示された際にモーターが非常に強く動くという現象が確認できました。
- 🔌 カーボンケーブルのチェックは済ませましたが、エラーは解消されませんでした。
- 🛠 コントローラーを分解し、内部の12個のMOSFETを確認することにしました。
- 🔧 多用測定器を使ってMOSFETのショートを検出する必要があります。
- 🟡 黄色と青色のフェイスワイヤーにショートが見つかりました。
- 🔫 ショートが確認されたMOSFETは、ネガティブとポジティブの両方のMOSFETでした。
- 🛒 壊れたMOSFETのモデルナンバーを確認し、オンラインで同じものを注文しました。
- 🔨 新しいMOSFETを取り付けるためには、はんだづけが必要です。
- 🔄 修理後、エラーコード09は表示されなくなりました。
- 🚴♂️ 最後に、修理したコントローラーを組み立て直し、テストライドを行いました。
Q & A
ビデオではどのような問題が解決されていますか?
-ビデオでは、エラーコードゼロナインと呼ばれるエレクトリックバイクのコントローラーの問題が解決されています。これはモーターが非常に重く感じるという現象と関連しています。
エラーコードゼロナインが示すのはどのような状態ですか?
-エラーコードゼロナインは、コントローラーに問題があることを示しており、特にMOSFETがショートしていることが原因とされています。
コントローラーのトラブルを特定するためにどのようなツールが必要ですか?
-コントローラーのトラブルを特定するためには、マルチメーターと連続モードでテストを行い、MOSFETのショートを検出する必要があります。
MOSFETとは何ですか?
-MOSFETとは、金属氧化物半導体場効果トランジスタの略で、電力を制御する半導体デバイスです。エレクトリックバイクのコントローラーには12個のMOSFETが搭載されています。
MOSFETがショートしているかどうかをテストする方法は何ですか?
-MOSFETがショートしているかどうかをテストするためには、マルチメーターを連続モードに設定し、電池の負の端子から各MOSFETの端子にテストします。
MOSFETがショートしている場合、どのような対策が必要ですか?
-MOSFETがショートしている場合、そのMOSFETを新しいものに交換する必要があります。
MOSFETを交換する際にはどのような作業が必要ですか?
-MOSFETを交換する際には、まずMOSFETを取り外し、新しいMOSFETのモデルナンバーを確認し、必要な場合はオンラインで購入する必要があります。次に、はんだごてを使って新しいMOSFETをはんだづけします。
ビデオではどこでMOSFETを購入していますか?
-ビデオでは、MOSFETをオンラインショップから購入しており、10個で約300ペソというコストで入手しています。
MOSFETを交換した後、どのようなテストを行いますか?
-MOSFETを交換した後、最初にショートの有無をテストし、次にエレクトリックバイクに取り付けてスロットルやペダルアシストが正常に機能するかどうかを確認します。
エラーコードゼロナインを解決するためにかかった費用はどのくらいですか?
-エラーコードゼロナインを解決するためにかかった費用は、MOSFETの購入費用のみで約300ペソです。
このビデオがどのように役立つと感じる場合、どのようなアクションをとらなければなりませんか?
-このビデオが役立つと感じた場合、それを友達と共有したり、ビデオを高評価にしたりすることが推奨されます。
Outlines
🛠️ エラーゼロナインのトラブルシューティング
ビデオでは、エラーコードゼロナインが表示されたE-バイクのコントローラーの問題を解決するプロセスが紹介されています。ライダーはモーターが非常に重く動くことに気づき、ケーブルのチェックを試みましたが、問題は解決されませんでした。コントローラー自体に問題があると推測し、分解して内部のMOSFETを調べることにしました。12個のMOSFETがあり、マルチメーターを使ってショートを探査し、黄色と青の線のペアでショートが見つかりました。
🔍 MOSFETのショートを特定
MOSFETのショートを特定するために、ビデオでは2つのMOSFET間のショートをテストする方法が説明されています。ショートが確認されたMOSFETは黄色の線に接続されており、それらは問題の原因と判断されました。修理のためにMOSFETを交換する予定で、新しいMOSFETを見つけるために地元のショップをチェックしたり、オンラインで注文を検討したりすることも提案されています。
👷♂️ 新しいMOSFETの取り付け
新しいMOSFETを取り付けるプロセスがビデオで紹介されています。MOSFETを取り外し、新品に交換するためには、はんだごてを使用して配線を切断し、新品をはんだ付けする必要があります。はんだ付けの前にfluxを塗ることで接着力を高め、修理の質を向上させています。修理が完了したら、ショートを再度確認し、E-バイクに取り付けて動作確認をしています。
🚴♂️ エラーゼロナインの修復完了とテスト
修理が完了し、E-バイクのコントローラーを再アセンブルしてテストしています。エラーコードゼロナインは表示されず、サドルを漕ぐことでパドルアシストが機能することを確認しました。MOSFETが再度故障しても、手持ちの8個のMOSFETで交換できると示唆しています。ビデオは、エラーゼロナインを修復し、費用を大幅に削減する方法について役立つと感じる視聴者に高評価と共有を呼びかけています。
Mindmap
Keywords
💡エラーコード
💡LCDスクリーン
💡モーター
💡ケーブル
💡コントローラー
💡MOSFET
💡マルチメーター
💡ショート
💡はんだづけ
💡テストライド
Highlights
E-bike encountered an error code 09 on the LCD screen indicating a controller problem.
The motor was turning hard, suggesting a physical obstruction or issue.
Cables were checked first, but the error persisted, pointing to a controller malfunction.
Disassembly of the controller revealed 12 MOSFETs, two in each phase wire.
A multimeter in continuity mode was used to test for short circuits in the MOSFETs.
Testing showed one pair of MOSFETs on the yellow phase wire was shorted.
Identified the faulty negative MOSFET as the cause of the short circuit.
Decided to replace the shorted MOSFETs to resolve the controller issue.
Removed and replaced the faulty MOSFET with a new one.
Purchased the replacement MOSFETs online for approximately 300 pesos for 10 pieces.
Used a soldering iron to remove and install the new MOSFET.
Checked for shorts after soldering the new MOSFET to ensure proper installation.
Successfully repaired the error code 09 by replacing the busted MOSFET.
The repair cost was minimal, only 300 pesos, making it a cost-effective solution.
Assembled the controller back together and prepared for a test ride.
No error code 09 appeared after reassembly, indicating a successful repair.
The pedal assist function was tested and confirmed to be working properly.
The video provided a step-by-step guide for repairing an e-bike controller, offering practical help for viewers.
Transcripts
let's turn this thing on
[Music]
my e-bike has a new problem
and this is the problem
so it has an error
zero nine and the lcd screen
and it says that
the controller is
having problems
oh what a bad news
i just happened to
see this one one while i was driving
and the only thing that i could notice
is that the motor
turns really really hard
it seems that something is holding me
back
so i already tried to check the cables
and still
the
error is still there
so i think the problem really is
the controller itself
so let's try to
check this one out
and see
if we could figure what's wrong with
this controller
okay
okay so we have already disassembled the
controller
which is this the case
and
this is the inside part of the
controller
see so the controller has 12 mosfets on
it
two in each of the face wires so this
one is the yellow green and the blue
so in order to check
if which of these
mosfets are shorted out
we need a multi-tester and put it in
continuity mode
to test out any short
of the mosfets
so to test the mosfet
we will test it
from
the negative
battery terminal towards each of the
uh
face wires okay
so negative
let's double check first
search in continuity mode
so let's try first
on the yellow
face wire and see if
this one is shorted also
so there's no short in here
okay
okay this one is shorted out
also this one
the next one is good
next is good
another one is good
good
good
and the rest are all okay except for
one of the pair
on the
yellow
uh
face wire
this one here
so the neck this is i think the negative
mosfet here
as this one is the positive mosfet
here
okay so this one is the positive muscle
but still even if
put it in positive it will be shorted
out still
so negative muscle
positive muscle
negative
positive mosfet
negative
positive muscles
[Music]
this one right here
is our
suspect
mosfet
as this one
is the one shorted out with respect to
ground
so as we
clip this one on the other side
so let's check here
on
the two mosfets
by shorting it out
by testing a shortage
in between the legs of the mosfet
so it is this one here
so this one is shorted out
also shorted up
this one is also shorted
unlike the rest of the mosfets
it doesn't short out
here
[Music]
okay
so this
uh two mosfets here
are our suspect
so let's try to change this one
and hopefully we'll be able to
solve the problem if not
then we'll be needing a new controller
for the e-bike
okay
so we'll try to remove this
mosfet here
and replace it with the new one
okay so let me just
get the soldering irons that we can
remove and check the part number for
this one
um
[Music]
okay
um
[Music]
so this is now the mosfet
that is being shorted out
so i'll just place here somewhere the
model number
and
we'll try to find here at our local shop
if we could buy this thing up
if not then we'll have to order online
okay
so the most patent that we ordered
from shelby online
already came and
this is how the packaging looks like
they are 10 pieces
and cost around 300 pesos or
10 of them
okay so try to
remove this one
so
for this one we'll be needing only two
okay here
let's check them out first and test
so
okay so using the tester we'll check
there are shortages
okay
so it's good
so it's time to solder this one in here
so to install the mosfet we need to
remove screws and installing them
come on
okay so now that they're in
it's time to solder on the other side
okay we'll try to put a little bit of
the flux
on the shoulder
[Music]
ah
[Music]
okay so we're now done soldering the
mosfet so it's time to check for short
okay
so we're now done with installing the
new mosfet so it's time to test it out
in the e-bike
and let's see if error is still there
okay so time to test out the controller
so we have already here the new mosfet
soldered out here the back
so hopefully we could test this one by
testing out the
throttle here
so we have already connected the power
supply to the battery
the display and the connection towards
the motor here
and
let's turn this thing on
okay
so far
no more
here or zero dying
[Applause]
okay so let's check if the truffle works
here
first
[Applause]
yes
so the throttle didn't work
shut it out again
yes
okay so with this one we have
successfully repaired
the error zero nine which is the busted
mosfet
on the controller itself
so we've only cost around
300 pesos
so let's assemble the whole thing first
and
have it on a test ride okay
okay so we have already rewired
everything and put it back to its
thermal position
after replacing the bad mosfet in this
controller
so let's try to turn it on once again
okay no more error zero nine
so let's try if
the pedal assist works by
pedaling on
the cranks
nice it's not working
okay so we have successfully repaired
the error zero nine on this controller
and hopefully
this will board out anymore the mosfet
so even though if the mosfet fails again
we still have an available eight pieces
of mosfet that we can replace
by the time it gets burned up or shorted
out again
okay
so if you think that this video is
helpful for you then just give it a like
and share it with your friends
see you in the next one
so
5.0 / 5 (0 votes)