What glue is best for your camera leatherette? Testing some suggested adhesives for camera repair!
Summary
TLDRこのビデオでは、レトロカメラのレザーエットを再接着するための接着剤の選び方について解説しています。修理に必要な接着剤は、接着後も動かすことができる柔軟性と、長期間持続する強さが必要です。また、カメラの修理や分解を容易にするために、接着剤は除去可能でなければなりません。様々な接着剤を実際に試し、その強さと除去のしやすさを比較しています。結果として、E6000やダブルサイトテープが最適な選択肢として勧められています。
Takeaways
- 📷 スクリプトは、レトロカメラのレザーエットを貼り直すための接着剤について話しています。
- 🔍 作者は、ネット上の意見を集めて、実際に11種類の接着剤をテストすることを計画しています。
- 🛠 接着剤は、接着後に移動可能で、長期間しっかり貼り付く必要があります。また、レザーエットやカメラを傷つけず、いつでも剥がせる性質が必要です。
- 🔬 作者は、メーカーの指示に従って、またはそれに反して接着剤をテストし、どちらが最良の結果を出すかを検証します。
- 🐵 テストに使われる素材はアルミニウムと、ブロニカS2Aのクロムメッキされた不銅鋼ボディで、非多孔性金属として同様の目的を果たすと述べています。
- 👨🔧 テストに用いた接着剤には、ゴリラ接着剤、接着剤、スーパーグル、エルマーズPVA接着剤、スプレー接着剤、ボスティック接着剤、E6000、ユーフロ接着剤、両面テープなどがあります。
- 🚫 スーパーグルはレザーエットに悪影響を与える可能性があり、使用しないことを勧めています。
- 👍 E6000は、接着力が強く、クリーニングが容易で、クリアで粘着性のある特性を持っており、良い結果を出したと評価されています。
- 🔄 両面テープは、接着が容易で、再貼り付けが可能で、カメラから剥がしやすく、作者が最も満足している接着方法の一つだと述べています。
- 🔑 最も重要なのは、接着剤が作者の要件を満たすことで、接着がしっかりしていて、剥がしやすさを保ち、カメラやレザーエットを傷つけないことです。
- 📝 作者は、コメント欄で異なる意見があることを理解しており、最適な接着剤は個人のニーズに応じて異なるかもしれないと述べています。
Q & A
ビデオで紹介されたのはどのカメラのモデルですか?
-ビデオで紹介されたカメラモデルはBronica S2Aです。
ビデオの主題は何についてですか?
-ビデオの主題は、古いカメラのレザーエットを剥がれたり貼り直しが必要な場合にどの接着剤を使うかについてです。
接着剤を選ぶ際の重要なポイントは何ですか?
-接着剤を選ぶ際の重要なポイントは、接着剤が接着した後もカメラやレザーエットを傷つけず、数年間しっかり接着し続ける能力があること、また必要に応じて接着剤を剥がすことができることです。
ビデオで試した接着剤は何種類ありますか?
-ビデオでは11種類の接着剤を試しました。
ビデオで使用した接着剤のテスト方法は何ですか?
-ビデオではメーカーの指示に従った方法と、それに従わない方法で接着剤をテストしました。その後、接着剤の接着力を確認し、24時間以上経過した後に接着剤を剥がしてみました。
ビデオで試した接着剤の中で、最も適切だと思われる接着剤は何ですか?
-ビデオの結果から、最も適切だと思われる接着剤はE6000とダブルサイドテープのようです。
ビデオで使用した接着剤のどれが最悪の結果だったと述べられていますか?
-ビデオで述べられた最悪の結果はスーパーグルです。それはレザーを破壊し、接着力を高める代わりに不良な影響を与えたと報告されています。
ビデオで使用した接着剤の中で、接着力を高めずに簡単に剥がせる接着剤は何ですか?
-ビデオで使用した接着剤の中で、接着力を高めずに簡単に剥がせる接着剤はエルマーのPVA接着剤や強力PVA接着剤が挙げられます。
スクリプトの内容に基づいて、どのような接着剤がカメラのレザーエットに適しているかを示す実験が行われましたか?
-ビデオでは、メーカーの指示に従い、またそれに従わない方法で、11種類の接着剤を試し、それぞれの接着力を比較して、カメラのレザーエットに適した接着剤を探求しました。
ビデオで使用した接着剤のどれが最も簡単に剥がせることができたと述べられていますか?
-ビデオで述べられた最も簡単に剥がせた接着剤はダブルサイドテープのようです。
ビデオの最後に、カメラのレザーエットを貼り直す際に勧められる接着剤は何ですか?
-ビデオの最後に勧められた接着剤はE6000とダブルサイドテープです。これらの接着剤は接着力が高く、必要な時に簡単に剥がすことができるという利点があります。
Outlines
📷 レトロカメラのレザーカバーの接着
ビデオでは、レトロカメラのレザーカバーの再接着について説明しています。特に、ブロニカS2Aのレザーカバーが剥がれ始めたため、新たにレザーを貼り替えることにしました。接着剤を選ぶ際には、接着後も動かすことができる柔軟性と、長期間持続する強さ、レザーやカメラに傷をつけない性、また必要に応じて剥がせることが求められます。plyo bondという接着剤が製造業者で使用されているとされていますが、英国では入手困難であるため、手元にある様々な接着剤を試してみることにしました。
🔍 接着剤の比較実験
11種類の接着剤を比較実験し、それぞれ製造業者の指示に従った方法とそうでない方法で試しました。アルミニウム板を使ってテストを行い、接着剤を均等に塗布し、接着力を比較しました。ゴリラ接着剤やコンタクト接着剤、スーパーグル、PVA接着剤、スプレー接着剤、ダブルサイドテープなど多岐にわたる接着剤を試し、接着力と剥がしやすさを評価しました。
🏆 接着剤の実験結果
実験結果を評価し、接着剤の適切さを判断しました。スーパーグルはレザーに悪影響を与える一方で、PVA接着剤は接着力が十分ではなかったため、これらの使用は避けるべきだと結論づけました。一方、e6000やBostikの接着剤は接着力が強固で、剥がしやすさをも保ちました。ダブルサイドテープは、接着が均一で、剥がしやすく、清潔に剥がせることができたため、特に優れた結果を示しました。
👍 おすすめの接着剤
最終的にダブルサイドテープとe6000接着剤が最適な選択であると判断しました。これらの接着剤は接着力が強固でありながらも、必要な時には簡単に剥がすことができるという利便性を持っています。他の接着剤と比較して、特にダブルサイドテープは事前に接着剤を貼り、均一な接着を確保し、剥がしやすさを兼ね備えているという利点があります。このビデオはカメラのレザーカバーの接着に関する参考になるでしょう。
Mindmap
Keywords
💡レザーエット
💡接着剤
💡ブロニカS2A
💡接着条件
💡テスト
💡プライヤーボンド
💡接着力
💡除去可能性
💡ダブルサイトテープ
💡E6000
Highlights
Introduction to the topic of using glue to re-stick leatherette on vintage cameras.
The presenter's own Bronica S2A camera is being used as a test subject for the glue experiment.
Leatherette on vintage cameras often peels away and needs re-gluing.
Different types of glue have been suggested online for re-stick leatherette.
The glue needs to be specific for the task, allowing for movement and long-term adhesion without damaging the leatherette or camera.
Plyo bond is mentioned as the manufacturer's choice, but it's hard to find.
Contact adhesives are being tested as alternatives to Plyo bond.
Eleven different types of glue are tested in various ways.
Aluminium and chrome-plated stainless steel are used as materials for testing adhesives.
Gorilla Glue is tested both according to and not according to manufacturer's instructions.
Super Glue is tested and found to damage the leatherette.
Elmer's School PVA Glue and Strong PVA are tested for their adhesive properties.
Spray adhesive and Bostic Contact Adhesive are tested for their tackiness and bond strength.
E6000 is tested as a recommended adhesive for its clarity and bond strength.
Double-sided tapes are tested for ease of application and removal.
Results are shared after a week for a thorough assessment of the adhesives' performance.
Gorilla Glue, when not applied according to instructions, forms a very strong bond.
Super Glue is not recommended due to its damaging effects on the leatherette.
PVA adhesives are found to be not strong enough for the task.
Spray adhesive and Bostic Contact Adhesive are too strong and damage the leatherette.
E6000 provides a good strong bond that is also removable without damaging the leatherette.
Double-sided tapes, particularly the Tesa brand, show promise for easy application and clean removal.
The presenter emphasizes the importance of choosing an adhesive that meets specific needs for the task.
The video concludes with a summary of the most suitable adhesives for re-sticking leatherette on vintage cameras.
Transcripts
[Music]
good evening everybody welcome back to
the 120s
today we're out in the workshop and we
are talking about glue
specifically what glue to use to stick
down or re-stick down
the leatherette on your vintage cameras
this is my trusty bronica s2a
um and as you can see it's uh the the
leatherette is really starting to peel
away in a few places
so i'm planning to re-skin this all
together i'm planning to get rid of this
old leatherette
um and replace it with a whole new one
so
for that i've been trying to work out
what is the right
glue to use to stick down the new
leather app
and it seems to be something of a bone
of contention um
there seem to be a hundred different
opinions around the internet about what
is the right glue to use
so i figured the best thing i could do
is take all of those suggestions
everything that people online have
suggested be used
uh and test it all now the glue that you
use to stick down
a leatherette actually needs to be quite
specific because there's certain jobs
that it needs to do
number one is that when you put the
leather when you when you apply the glue
put the leather onto the body it kind of
needs to be
movable for a short period of time to
make sure you can get it fully lined up
whatever glue you use also needs to be
it needs to hold firm for several years
it needs to not destroy the leatherette
it needs to not destroy the camera but
it also needs to be removable
you need to be able to take the leather
off again at some point
because invariably almost all cameras
are hiding stuff
underneath the leatherette usually a lot
of screws that you need to
to get at to dismantle the camera are
covered by the leatherette
and therefore you want it to stay on
but you also want to come off when you
wanted to
plyo bond is generally accepted to be
what the manufacturers use um
you can't get i can't i certainly can't
find anything
they're specifically called plyo bond
here in the uk
uh but as i understand it player bond is
a type of contact adhesive
so i've got hold of several different
contact adhesives on pretty much
everything i can get my hands on
i'm going to try them all i'm going to
try them in a few different ways
according to manufacturer's instructions
and we'll try it not according to
manufacturer's instructions and see
which one works best
so here we go i actually have 11
different types of glue that i'm going
to test today
this is the material i plan to be using
quite like it
i have a strip of aluminium
which i normally use to cut lens boards
from now
the body of the s2a is chrome plated
stainless steel so
it's not exactly the same but it's a
non-porous metal
so it should serve the same purpose for
now so we'll start with the
gorilla glue all right then so i'm going
to do as the manufacturer suggests
apply to both sides so spread
fairly evenly across there and spread
across aluminium aluminum
i should say we'll leave that to dry a
bit
and in fact the next one i'm going to do
uh is
the same thing contact adhesive not
according to the manufacturer's
instructions
so same again put that to one side now
this one i'm going to stick down
straight away
so spread it a bit here we go
i should really have gloves on right
let's put this top one on
i mean that definitely forms a stronger
bond instantly
next up is the old super glue
so i find a small piece for this because
i'm fairly certain we're not going to
use this
fairly well spread oh
this is bloody typical super glue super
blue okay next we'll do this one this is
something that was recommended by
somebody online elmer's school
pva glue
[Music]
and then we're going to do
strong pva medium
and stick that on there
let's go with the um the no-nonsense
spray contact adhesive
do this one next wow
okay and then we're going to stick it
down oh
it's bubbling there's a reaction going
on
okay next up another contact adhesive
this one
bostic leave until the glue is just
tacky approximately four minutes at room
temperature
okay that over there and then we'll just
give this a little spread as well
is this tacky yet yeah i think so
all right there we go right next up this
is e6000
plus a few blobs along there
i'm not going to spread this one because
it says to
make the surfaces okay and then we're
gonna
peel the surfaces apart and it says wait
five minutes
next up
after 10 minutes press together briefly
and firmly
right i am now going to apply the e6000
now the next thing i'm going to try
double-sided tape
first
apply now i'm going to cut around it to
a certain extent
and i am now going to peel away the
other side of the double-sided tape
ah here we go put a corner
okay and then
double-sided tape
no oh i'm still putting down let's put
the yoohoo down
right then here is the uh
finished product so we've got from the
top
gorilla glue used according to
manufacturing instructions
gorilla glue not according to
manufacturer's instructions
super glue elmer's pva strong pva
spray glue ostic contact
e6000 yuhu contact
double-sided tape double-sided tape so
yeah it'd be really interesting to see
how those come out
um i'm going to put them in a safe place
away from the kids
so they don't get tinkered with and um
come back
in uh
tomorrow wednesday thursday for a bit
more than 24 hours and then we'll we'll
have a tug at them with a pair of pliers
and um see which one is the most
appropriate
not the strongest which one's the most
appropriate so i'm gonna put that down
right then here we are for the results
it has been
um probably more like a week actually i
was gonna give it 24 hours but it's been
probably about a week so plenty of time
for this stuff to cure
properly i am now going to go through
these one by one
see how the stick is first of all see
how good that feels
then i'm going to try and pull it with
my fingers um see if i can get it off
and then if it's a struggle i'll use a
pair of pliers obviously what we're
looking for is
um it needs to be a good stick
but kind of removable fairly easily and
without
destroying the um leather wrap
so the fir the first one at the top is
the
gorilla glue clear contact adhesive
the very top one is um i
attached according to the instructions
it's a good solid bond
it's not moving so let's try and take it
off
so here we go oh jesus
that's not bad actually let's now try
same glue guerrilla clear contact
adhesive
this one applied not according to the
instructions so this is just
jammed on oh god
if anything is a bloody stronger bond
than with the uh that's pretty good
actually
it comes off pretty cleanly
i don't have it here but this next up is
the super glue plain old super glue
there it is ah
so that's um wow
yeah so that is um it's completely
breaking apart
if you look bits of the leatherette are
ripping off
see if i can even get it all off
[Applause]
wow i would not want this to be stuck to
my camera
so it i think the super glue has
actually
had quite a negative effect on the
leather actually
i'm gonna stop with that now um
don't use super glue whatever you do
jesus
right next up elmer's school pva
so i'm just i expect this one's going to
come off pretty easily but let's have a
look
still sticky underneath actually i mean
it's a relatively strong bond you know
it was um
fairly well held but definitely comes
off easily so i think
the corner of that starts to lift with
the elmer's glue on it
i think the rest of it's going to come
off pretty quickly so that one's
probably not for me i don't think
next up is the
strong art pva
this one i suspect this one will be
similar i think pvas are you know
generally designed to stand up to much
punishment
so here we go oh actually it's a pretty
strong bond
it's not bad at all
wow
pretty good quite impressed by that next
one is the spray adhesive which i'm not
um
it took ages to stick down it's really
wet
um let's have a look
not bad actually
i don't think i think not as good as the
pva uh the strong pva
plus it's really sticky yeah yeah not
not convinced about that one
uh next up bostick contact adhesive
there it is let's give this a go
wow that is again we did this according
to the manufacturer's instructions
and that is a really tight bond
yeah so let's get a pair of pliers on
that let's see what happens
oh jesus yeah a lot of it's um
coming off on the
yeah it's it's broken up a little bit so
that's just too strong too
strong e6000
e6000 plus crystal clear
which is another contact adhesive
similar formula to the rest of them
it's another one that's recommended this
one's not bad
so a good a good strong stick
but with a kind of moderate amount of
effort
comes off and it is clear
kind of gummy not too sticky
so that's quite a good one actually
[Music]
e6000
next up is the yuhu flexible and
transparent
all-purpose power so here we go
corner here that's tough
yeah so that's this i think is similar
to bostic probably a bit too much
okay
that's left a lot of um left a lot of
the leather wrap
on here you can see the patterning from
the back
so a little bit too much i'd say next up
are the two tapes and remember these are
these ones i
kind of hope will work because um
uh because if they do then
it's gonna be a very easy application
and it's you know uniform
i think this is that's pretty good huh
that's pretty good
and even that with a there was a split
in that and it hasn't
torn it now um it's mostly stayed on
here which is interesting
there's obviously another important
factor here is is whether or not we're
going to be able to get the adhesive
off the camera and whether it will clean
up
certainly not coming off easily so that
was that tape
my brand we've now got this one which is
the
tessa teaser table
now interestingly so that's all coming
off on the leatherettes
actually sticks down again i think
i think it might be the tape you know
[Music]
come off very clean but it's all on here
if you're gonna then get this tape off
here
how about that ready for reapplication
well i think we have a winner to be
honest
because
you can pre-apply it
so you can put sticky tape double sided
tape
all across the bit of leatherette that
you're working with
then cut it so you know that you have
completely kind of uniform
spread
you can then peel away the backing stick
it down
um and it looks like that is going to
come off pretty easily
leaving your leather air completely
untouched
um and and
the metal just needing to clean but that
really has worked really well i'm happy
that
that e6000 was very good as well
impressed with that
super glue big no no don't use superglue
whatever you do
pva i don't think is strong enough spray
was a bit rubbish
everybody has different ideas as to what
is the right stuff what is the best
stuff to use to uh to stick down your
leatherette
so no doubt i'll get panned in the
comments oh you didn't try this you
didn't try that
i can't i'm gonna buy every glue on the
market there are potentially
many different answers to the question
um
the most important thing is you're
sticking it down with something that
you're happy with
uh and it's going to do what you need it
to do
which is a quite unique job you need to
stick down be completely firm not peel
at the corners
and and yet peel off whenever you ask it
to
so um there we go
i hope you found this useful bye now
you
Посмотреть больше похожих видео
Replacing Camera Leather and Gluing Leatherette onto a Camera, also Works for Rubber Grips
【整腸剤】ビオフェルミン、ビオスリーなど整腸剤について徹底解説//整腸剤を飲む時の注意点も説明します。
KT Tape: Neck and Shoulder
Changer Trynowドライブレコーダー ミラー型 前後カメラ、起動不良をDIY修理しました。参考にしてください。 Changer V28 / Trynow V28
【腸活】一番いい整腸剤はどれか?新ビオフェルミンS、ビオスリー、エビオス、強力わかもと、ザ・ガード
【いつからない?】新車からスペアタイヤがなくなった理由を説明します
5.0 / 5 (0 votes)