Foster Seeley Discriminator: Basics, Circuit, Working, Advantage, Disadvantage | Com Sys | Lec 81|
Summary
TLDRThis video discusses FM signal demodulation using the phase discriminator method, focusing on three techniques: Foster-Seeley discriminator, ratio discriminator, and phase-locked loop. The video begins by addressing the Foster-Seeley method, highlighting its ability to overcome limitations in balanced slope detectors, such as linear characteristic issues. The circuit design simplifies by tuning all three tank circuits to the same frequency. It explains the functioning of the discriminator in detail, discussing voltage differences and phase angles at different frequencies. The video concludes by outlining the method's advantages and drawbacks.
Takeaways
- 😀 FM signal demodulation using the phase discriminator method is covered in this video.
- 📡 Three methods of phase discrimination are discussed: Foster-Seeley discriminator, ratio discriminator, and phase-locked loop demodulator.
- ⚡ The Foster-Seeley discriminator helps overcome limitations of balanced slope detectors, offering improved linearity and design simplicity.
- 🔧 The circuit includes three tank circuits tuned to a specific frequency, simplifying the design.
- 🧲 Coupling capacitors are used to block DC voltage, allowing only the necessary frequency to pass through.
- 📈 When the input frequency is the same as the carrier frequency, the output voltage is zero due to a 90-degree phase difference.
- 🔀 If the input frequency is higher than the carrier frequency, the phase difference decreases, producing a positive output voltage.
- 🔄 When the input frequency is lower than the carrier frequency, the phase difference increases, resulting in a negative output voltage.
- 👍 The Foster-Seeley discriminator offers a better linear characteristic compared to balanced slope detectors.
- ⚠️ A limitation of this method is the lack of a limiter circuit, which can introduce errors in output due to amplitude variations caused by noise.
Q & A
What are the two main methods used for demodulating FM signals?
-The two main methods used for demodulating FM signals are the frequency discriminator method and the phase discriminator method.
What is the main drawback of the balanced slope detector in FM demodulation?
-The main drawback of the balanced slope detector is its non-ideal linear characteristic, which can affect performance.
How does the Foster-Seeley discriminator address the drawbacks of the balanced slope detector?
-The Foster-Seeley discriminator overcomes the drawbacks of the balanced slope detector by using three tank circuits tuned to the same frequency, making the design simpler and more effective.
What is the role of coupling capacitors in the Foster-Seeley discriminator circuit?
-The coupling capacitors block DC voltage in the secondary windings and allow the frequency signals to be transmitted to the primary windings.
What happens to the output voltage when the input FM signal frequency is equal to the carrier frequency (Fc)?
-When the input FM signal frequency is equal to the carrier frequency (Fc), the phase difference between the primary and secondary voltages is 90 degrees, resulting in zero output voltage.
How does the phase difference between primary and secondary voltages change when the input frequency is greater than the carrier frequency?
-When the input frequency is greater than the carrier frequency, the phase difference between the primary and secondary voltages becomes less than 90 degrees.
What occurs in the Foster-Seeley discriminator when the input frequency is less than the carrier frequency?
-When the input frequency is less than the carrier frequency, the phase difference between the primary and secondary voltages is greater than 90 degrees, resulting in a negative output voltage.
What is the advantage of using three tank circuits tuned to the same frequency in the Foster-Seeley discriminator?
-The advantage of using three tank circuits tuned to the same frequency is that it simplifies the design and ensures a good linear characteristic in the phase discriminator.
What is the disadvantage of the Foster-Seeley discriminator?
-The main disadvantage of the Foster-Seeley discriminator is the absence of a limiter circuit, making it susceptible to amplitude variations caused by noise, which can introduce errors in the output.
How could a limiter circuit improve the performance of the Foster-Seeley discriminator?
-A limiter circuit could improve the performance by absorbing amplitude variations due to noise, preventing errors in the output signal and maintaining a constant amplitude in the demodulated signal.
Outlines
📡 Introduction to FM Signal Demodulation
In this introductory section, the speaker welcomes viewers to a lecture series on analog communication, specifically focusing on FM signal demodulation methods using phase discriminators. The three key methods discussed are Foster-Seeley discriminator, ratio discriminator, and phase-locked loop (PLL) demodulator. The section also recaps frequency discriminator methods such as simple slope detectors and balanced slope detectors, highlighting the issues with balanced slope detectors that Foster-Seeley aims to address, including improved linear characteristics and design simplicity.
🔧 Foster-Seeley Discriminator Circuit Design
This paragraph delves into the design of the Foster-Seeley discriminator circuit. It explains how the circuit uses three tank circuits, all tuned to a specific frequency (fc), making the design easier. The primary tank circuit and secondary coils are described in detail, including how coupling capacitors block DC voltage in the secondary windings while allowing the tuned frequency to pass through. The function of the phase discriminator and envelope detectors in the circuit is outlined, setting the stage for understanding its operation.
⚙️ Working of Foster-Seeley Discriminator - Case 1: Input Frequency = Fc
Here, the working principle of the Foster-Seeley discriminator is explained for the scenario when the input frequency matches the carrier frequency (fc). The primary and secondary voltages have a phase difference of 90 degrees. The induced voltages across the secondary windings are out of phase by 180 degrees due to the transformer’s center tap configuration. The output voltage is calculated by subtracting the two induced voltages, resulting in zero output voltage, confirming that when the input frequency equals fc, the output is zero.
📏 Working of Foster-Seeley Discriminator - Case 2: Input Frequency > Fc
This section explores the scenario when the input frequency is higher than fc. The phase angle between the primary and secondary voltages decreases to less than 90 degrees. The induced voltages are again out of phase by 180 degrees, but vector addition shows that v01 is larger than v02. Subtracting these gives a positive output voltage. This condition arises when the modulated signal's positive amplitude results in a frequency higher than fc.
📉 Working of Foster-Seeley Discriminator - Case 3: Input Frequency < Fc
In this paragraph, the case where the input frequency is lower than fc is discussed. The phase difference between the primary and secondary voltages exceeds 90 degrees. Vector addition reveals that v02 is larger than v01, leading to a negative output voltage. This negative value corresponds to the modulated signal’s negative amplitude, which reduces the frequency below fc. The explanation confirms the behavior of the Foster-Seeley discriminator when input frequencies fall below the carrier frequency.
📊 Advantages and Disadvantages of Foster-Seeley Discriminator
This final section outlines the advantages of the Foster-Seeley discriminator, including its simpler design due to all tank circuits being tuned to the same frequency and its superior linear characteristics compared to the balanced slope detector. However, a key disadvantage is the lack of a limiter circuit. This omission makes the circuit sensitive to amplitude variations caused by noise, which can introduce errors in the demodulated output. The video concludes by hinting at the next lecture, which will cover ratio discriminators.
Mindmap
Keywords
💡FM Signal
💡Phase Discriminator
💡Foster-Seeley Discriminator
💡Tank Circuit
💡Coupling Capacitors
💡Primary and Secondary Voltage
💡Phase Difference
💡Envelope Detector
💡Phase-Locked Loop (PLL)
💡Linear Characteristic
Highlights
Introduction to FM signal demodulation using phase discriminator methods, focusing on Foster-Seeley discriminator, ratio discriminator, and phase-locked loop.
Key objective of the Foster-Seeley discriminator method is to overcome drawbacks of the balanced slope detector, particularly in achieving better linear characteristics.
In the Foster-Seeley discriminator, three tank circuits are used, all tuned to the same frequency, simplifying the design compared to previous methods.
Coupling capacitors block DC voltage in secondary windings, ensuring proper signal transmission in the tank circuit.
The primary function of the tank circuit is to tune to a specific frequency and facilitate phase difference calculation between primary and secondary voltages.
When the input FM signal frequency matches the carrier frequency (Fc), the phase difference between the primary and secondary voltages is 90 degrees, resulting in zero output voltage.
When the input frequency is greater than the carrier frequency, the phase difference decreases, leading to a positive output voltage.
When the input frequency is less than the carrier frequency, the phase difference increases beyond 90 degrees, resulting in a negative output voltage.
The Foster-Seeley discriminator is more linear compared to the balanced slope detector, offering improved signal demodulation accuracy.
The design simplicity of the Foster-Seeley discriminator comes from the tuning of all tank circuits to the same frequency.
A notable disadvantage of the Foster-Seeley discriminator is the lack of a limiter circuit, which makes it susceptible to amplitude variations due to noise.
The absence of a limiter circuit means that any amplitude variations in the FM signal will reflect as errors in the demodulated output signal.
Inclusion of a limiter circuit would absorb amplitude variations, reducing errors in the output signal.
The video will next discuss the ratio discriminator method, another technique for FM signal demodulation.
The phase discriminator methods provide a more detailed approach to FM demodulation, addressing specific challenges in earlier frequency discriminator methods.
Transcripts
नमस्कार दोस्तों एनालॉग कम्युनिकेशन
लेक्चर सीरीज में आप सबका बहुत स्वागत है
दोस्तों इस वीडियो से हम एफएम सिग्नल को
डी मॉडले करने के लिए फेज डिस्क्रिमिनेटर
मेथड्स को इन डिटेल डिस्कस करेंगे फेज
डिस्क्रिमिनेटर में तीन डिफरेंट मेथड्स
होते हैं पहला फोस्टर सिले डिस्क्रिमिनेटर
मेथड दूसरा रेशो डिस्क्रिमिनेटर मेथड एंड
थर्ड फेज लॉक लूप डी मॉडले र तो इस वीडियो
में हम सबसे पहले फोस्टर सिले
डिस्क्रिमिनेट्स के बारे में बात करेंगे
तो मेनली आपके दो टाइप के मेथड्स थे किसी
भी एफएम सिग्नल को डी मॉडले करने के लिए
एक था आपका फ्रीक्वेंसी डिस्क्रिमिनेटर
मेथड और अब है आपका फेज डिस्क्रिमिनेटर
मेथड फ्रीक्वेंसी डिस्क्रिमिनेटर मेथड्स
में भी दो अलग मेथड्स हमने डिस्कस किए
सिंपल स्लोप डिटेक्टर एंड बैलेंस स्लोप
डिटेक्टर्स तो लास्ट में जो बैलेंस्ड
स्लोप डिटेक्टर्स हमने डिस्कस किया उसमें
कुछ प्रॉब्लम्स थी मैं वहां ऑलरेडी डिस्कस
कर चुका हूं तो जो फास्टर सले
डिस्क्रिमिनेटर है इसका ऑब्जेक्टिव यही है
कि जो बैलेंस्ड स्लोप डिटेक्टर था उसके जो
ड्रॉबैक्स थे वो ड्रॉबैक्स हम काफी हद तक
यहां पे ओवरकम कर लेते हैं
जैसे लीनियर कैरेक्टरिस्टिक बहुत परफेक्ट
हमें नहीं मिली थी डिजाइन थोड़ा सा
कॉम्प्लेक्शन सिले डिस्क्रिमिनेट्स में आप
देखोगे कि यहां पे भी हमने तीन अलग-अलग
टैंक सर्किट यूज किए हैं
यह एक दो एंड तीन लेकिन तीनों टैंक सर्किट
एक ही पर्टिकुलर फ्रीक्वेंसी पर ट्यून
होते हैं जिसकी वजह से डिजाइन आसान हो
जाता है तो यह आपका प्राइमरी टैंक सर्किट
है यह जो सेकेंडरी कॉइल है वह सेंटर टेप
ट्रांसफॉर्मर्स में है जिसमें अपर पार्ट
आपका है वह एक टैंक सर्किट है लोअर पार्ट
भी आपका एक टैंक सर्किट है तीनों टैंक
सर्किट एक पर्टिकुलर फ्रीक्वेंसी दैट इज
एफसी उसी पर ट्यून होते हैं फिर इसमें
एक हम कपलिंग कैपेसिटर्स और एक इंडक्टर्स
का यूज करते हैं यह हमारी कोई रेडियो
फ्रीक्वेंसी कॉइल है और यह हमारा कपलिंग
कैपेसिटर्स है कपलिंग कैपेसिटर्स का यूज
सिर्फ यह है कि हमारा जो सेकेंडरी
वाइंडिंग्स है उसमें डीसी वोल्टेज को वो
ब्लॉक कर देता है और इनपुट पे प्राइमरी
वाइंडिंग्स में हमारी जो फ्रीक्वेंसी है
वह हमारी सेंटर टेपट इस इंडक्टर्स में
फ्रीक्वेंसी भेज देता है तो यह इसका एक
मेन फंक्शन है बाकी कि ये हमारा है फेज
डिस्क्रिमिनेटर और यहां पर ये एनवलप
डिटेक्टर है ये आपका दूसरा एनवलप डिटेक्टर
है तो यह है इसका सर्किट डायग्राम ये है
इसके कंसीट एंट्स पार्ट और कपलिंग
कैपेसिटर्स का मैं ऑलरेडी बता चुका हूं अब
हम इसके वर्किंग की बात करेंगे वर्किंग
में सबसे पहले जो यहां पर एफएम सिग्नल हम
इनपुट कराते हैं तो एफएम सिग्नल अगर
बच्चे एफसी फ्रीक्वेंसी का है एफसी
फ्रीक्वेंसी का कब होगा जब आपका एफएम
सिग्नल में मॉडले इि सिग्नल मैग्नी
ूड्स का है तो आपको यह देखना पड़ेगा कि जो
प्राइमरी वोल्टेज है और जो हमारा सेकेंडरी
वोल्टेज है उसके बीच में फेज डिफरेंस
कितना होगा राइट तो यह आपका क्या है यहां
पे अगर एफसी फ्रीक्वेंसी जाती है तो उन
दोनों के बीच में जो फेज डिफरेंस है वो
हमारा 90 डिग्री का है प्राइमरी वोल्टेज
क्या है प्राइमरी वोल्टेज को हम मान लेते
हैं हमारी v इनपुट वोल्टेज है यहां पे जो
इनपुट आएगी उसको मैं प्राइमरी वोल्टेज कह
रहा हूं सेकेंडरी क्या है सेकेंडरी में
सेंटर टेपट के ऊपर की मैं बात करूं तो ये
v ए1 कह दूंगा और नीचे की मैं बात करूंगा
तो v ए2 होगा तो सेकेंडरी वाइंडिंग के
अप्पर पोर्शंस में जो वोल्टेज है वो होगा
v एव राइट ये हो जाएगा हमारा अब यहां पे
ओबवियसली यहां पे कुछ इंड्यूस्ड वोल्टेज
होगी यहां पे भी कुछ इंड्यूस्ड वोल्टेज
होगी राइट तो अब यहां पर यहां पर आपके पास
कितना पोटेंशियल होगा कुछ वोल्टेज यहां
इंड्यूस्ड हुई और इसके अक्रॉस हमारी क्या
है इनपुट वोल्टेज है किस वजह से बिकॉज ऑफ
दिस कपलिंग कैपेसिटर्स राइट तो अगर मैं इस
पॉइंट पर वोल्टेज फाइंड आउट करना चाहूं और
डायोड को अगर मैं आइडियल कंसीडर करूं तो
दिस वोल्टेज प्लस दिस वोल्टेज आपकी यहां
पर मिल जाएगी तो इसका मतलब मैं कहूंगा कि
जो v01 है वो मेरी होगी दैट इज v ए1 प्वी
इन राइट और ऐसे ही अगर मैं इस पॉइंट पर
वोल्टेज कंसीडर करूं तो क्या होगा यहां पे
यह वोल्टेज प्लस दिस वोल्टेज तो यानी v02
जो वोल्टेज है वो होगी v ए2 प्स v इ इस
पॉइंट पर भी वोल्टेज पता कर ली हमने तो अब
मैं क्या चाहता हूं जैसे हमारी एफसी
फ्रीक्वेंसी है इन दोनों के बीच में अगर
90 डिग्री का फेज डिफरेंस है तो मान लीजिए
बच्चे यहां पर मेरा यह v इनपुट वोल्टेज
ठीक है यह v इनपुट वोल्टेज है तो v ए क्या
है 90 डिग्री का फेज डिफरेंस है 90 डिग्री
का एंगल दोनों के बीच में यह बनेगा तो
यहां पर क्या हो गया v एव लेकिन v एव और v
ए2 यानी ये इंड्यूस्ड वोल्टेज और ये
इंड्यूस्ड वोल्टेज हमेशा एक दूसरे के 180
डिग्री फेस शिफ्ट प मिलेंगी बिकॉज ऑफ दिस
टर टेपिंग ऑफ ट्रांसफॉर्मर तो यानी इसका
मतलब यहां पर यहां पर क्या होगा v ए2 राइट
अब इन दोनों के जो 01 है वो क्या है v एव
प्लस व इन यानी यहां पर जो पोटेंशियल है
वह क्या होगा दिस पोटेंशियल प्लस दिस
पोटेंशियल तो यहां
पर इनका एडिशन कैसे करते हैं वेक्टर एडिशन
इनके बीच में पैरेलल लाइन खींच दी जाती है
और यहां पर हम डायगोनल इसको कनेक्ट कर
देते हैं और ये क्या होगा दैट इज v01 ठीक
है अब v02 क्या होगा इसी के साथ हमने क्या
किया एक पैरेलल लाइन ड्र कर दी यहां पे भी
ड्रॉ कर दी और इसके बीच में डायगोनल हम
यहां पे कनेक्ट कर देंगे तो ये जो एरो है
ये दिखाएगा v02 का फाइनली मुझे आउटपुट
चाहिए v न राइट आउटपुट कैसे आएगी इस पे जो
पोटेंशियल है vr1 पे और r2 पे जो
पोटेंशियल है उन दोनों का सबडक्शन होगा
रीजन बीइंग यहां पर सेंटर टेपट
ट्रांसफॉर्मर है तो यह दोनों अपोजिट
पोलरिटीज की होंगी तो यानी यह जो पोलैरिटी
है वही पोलैरिटी यहां जाएगी बिकॉज ऑफ द
पैरेलल कनेक्शंस यहां जो पोलैरिटी है वह
यही जाएगी यानी जो आउटपुट वोल्टेज
है वो वोल्टेज होगी आपकी v01 - v02 दोनों
का एंप्लीट्यूड बिल्कुल सेम है लेकिन
नेगेटिव साइन अगर बीच में है तो डेफिनेटली
v जी ऑफ टू यहां पर आपका जीरो वोल्ट रहेगा
तो पहला केस सक्सेसफुली डिस्कस कर चुके
हैं जब भी आपके इनपुट पर एफसी फ्रीक्वेंसी
जाएगी तो आउटपुट वोल्टेज हमारी जीरो
मिलेगी ऐसे ही अब हम बात करते हैं इनपुट
फ्रीक्वेंसी अगर एफसी फ्रीक्वेंसी से बड़ी
हो तो उस केस में हमारा जो फेज एंगल है वह
90 डिग्री से कम हो जाता है फेज एंगल
किसका फेज एंगल आपका इनपुट प्राइमरी
वोल्टेज और सेकेंडरी वोल्टेज के बीच का
फेज एंगल 90 डिग्री से कम होगा तो इसका
मतलब यहां पर देख लीजिए ये आपका v इन
है अगर इन दोनों के बीच में v इन और v एव
इसके बीच में अगर 90 डिग्री से कम है तो
कुछ ऐसा बनेगा यह हमारा क्या है v
एव और v एव और v ए2 हमेशा क्या होगा आउट
ऑफ फेज तो ये हमेशा ये मैंने बिल्कुल 180
डिग्री यहां लिख दिया दैट इज v ए2 ठीक है
अब इन दोनों का एडिशन v01 कहलाता है तो
इसके पैरेलल में मैंने एक लाइन ड्र कर दी
इसके पैरेलल में लाइन ड्र कर दी और यहां
पर मैंने डायगोनल जो कनेक्शन दिया यह मेरा
कहलाएगा v01 अब यहां पर क्या होगा मैंने
क्या किया 02 भी निकालना है मुझे तो इसके
पैरेलल में मैंने लाइन ड्र की और यहां पर
डायगोनल मैंने इसको एक्सटेंड किया तो ये
होगा मेरा v02 राइट और मेरा जो v न ऑफ t
अभी मैंने इस केस में डिस्कस किया था व
क्या होगा v01 - v02 v01 का
मैग्निटिया
देख लीजिए जब फ्रीक्वेंसी एफसी
फ्रीक्वेंसी से बड़ी जाएगी तो मैग्नी ूड्स
में यही होता है क्योंकि एफसी फ्रीक्वेंसी
से बड़ी फ्रीक्वेंसी तभी होगी जब मॉडले इि
सिग्नल की नॉन जीरो पॉजिटिव मैग्नी ूड्स
की वजह से वो वेरिएशंस दिखाई दें एफएम
सिग्नल्स में थर्ड केस पे आ जाइए अगर आपकी
इनपुट फ्रीक्वेंसी एफसी फ्रीक्वेंसी से कम
हो तो वह कैसे होगा इस केस में आपका जो
फेज एंगल है किसके बीच में प्राइमरी
वोल्टेज और सेकेंडरी वोल्टेज के बीच का जो
फेज एंगल है वो हमेशा 90 डिग्री से ज्यादा
र
90 डिग्री से ज्यादा है तो कैसे होगा देख
लीजिए मान लीजिए यह आपका क्या है यह मेरा
इनपुट है यानी प्राइमरी वोल्टेज प्राइमरी
वोल्टेज आपकी न है जीरो डिग्री प फेज एंगल
90 डिग्री से ज्यादा है तो यहां पर तो 90
बनता है तो मैं क्या कर दूंगा अबकी बार
अबकी बार में इसको मान लूंगा यह है मेरा
बच्चों व
एलव एव यानी ये जो टैंक सर्किट है इस पर
जो इंड्यूस्ड वोल्टेज पैदा हुई v ए1 उसका
और इनपुट वोल्टेज के बीच का फेज डिफरेंस
90 डिग्री से ज्यादा है इसके बीच का एंगल
आप चेक करोगे तो 90 डिग्री से ज्यादा आपको
दिखेगा राइट अब नेक्स्ट अगर यह v एव यहां
है तो इसके ठीक 180 डिग्री यानी इसके जस्ट
अपोजिट क्या होगा vl2 बिकॉज ऑफ द सेंटर
टेप ट्रांसफॉर्मर यहां जो पोलैरिटी होगी
उसके ठीक अपोजिट यहां पोलैरिटी होगी
अपोजिट यानी नेगेटिव साइन नेगेटिव साइन
यानी 180 डिग्री ठीक है अब इसके बाद क्या
होगा अब इनको एक्सटेंड कर
दीजिए जब आप इनको एक्सटेंड करेंगे तो क्या
यहां पर क्या दिखेगा
आपको इसके पैरेलल ये लाइन बना दीजिए और
इसके पैरेलल ये लाइन बना दीजिए और इसको
डायगोनल कनेक्ट कर दीजिए इन दोनों का सम
क्या है
v01 और यहां पे क्या होगा
यहां पर भी आप डायगोनल इनको कनेक्ट कर
दीजिए इन दोनों का सम क्या है
02 यहां देखने से पता लगता है कि 02 जो
डायगोनल लाइन है इसकी लेंथ एज कंपेयर टू
01 काफी ज्यादा है तो जो आउटपुट वोल्टेज
है वह क्या होती है v01 माइनस v02 v01
यानी इसके अक्रॉस जो पोटेंशियल है यानी
यहां पर जो पोटेंशियल है राइट v0 यानी
यहां पर जो पोटेंशियल आया बट दोनों आउट ऑफ
फेज है नेगेटिव साइंस के साथ इसीलिए दोनों
का सबक्स होगा तभी मुझे v ऑफ नोट मिलेगा
बट यहां पर v02 एज कंपेयर टू v01 बड़ा है
तो v02 आपका v01 से बड़ा है तो मैं यह कह
सकता हूं कि यह वैल्यू डेफिनेटली जीरो से
कम होगी यानी नेगेटिव वैल्यू होगी नेगेटिव
वैल्यू होगी यहां से फिर से वेरीफाई हो
चुका है रिजल्ट एफसी फ्रीक्वेंसी से भी कम
अगर एफ सिगनल की फ्रीक्वेंसी है तो यानी
मॉडले इि सिग्नल कोई नेगेटिव एंप्लीट्यूड
का है इसीलिए वो उससे कम हुई है और यहां
पर वह वैल्यू नेगेटिव ही हमें रिसीव होती
है दिस इज हाउ वी कैन एक्सप्लेन द वर्किंग
पार्ट ऑफ दिस फोस्टर सिले डिटेक्टर्स
लेकिन इसके बाद इसकी कुछ एडवांटेज की बात
की जाए तीन टैंक सर्किट जरूर है बट तीनों
टैंक सर्किट एफसी फ्रीक्वेंसी प ही ट्यून
है जिसकी वजह से इसका डिजाइन कंपेरटिवली
काफी सिंपल है तो इसमें कोई कॉम्प्लेक्शन
नहीं है ठीक है दूसरी बात एज कंपेयर टू
बैलेंस्ड स्लोप डिटेक्टर इसकी लीनियर काफी
अच्छी है तो लीनियर कैरेक्टरिस्टिक ऑफ दिस
डिस्क्रिमिनेटर इज वेरी गुड बट
डिसएडवांटेज क्या है डिसएडवांटेज यहां पर
सिर्फ एक है वह क्या लिमिटड सर्किट का यूज
नहीं किया है लिमिटड सर्किट ऐसा सर्किट
होता है जो एंप्लीट्यूड की वेरिएशंस को
आउटपुट पर रिस्पांस ना दे यानी यह एफएम
सिग्नल है यहां पर अगर कोई नोइज आया तो
एफएम सिग्नल का जो एंप्लीट्यूड है नोइज की
वजह से चेंज हो सकता है अगर वह
एंप्लीट्यूड चेंज होगा तो आउटपुट पर भी
रिफ्लेक्ट होगा और आउटपुट पर जरूर हमारा
कुछ ना कुछ एरर इंट्रोड्यूस हो जाएगा इन
दी मॉडले इि सिग्नल लेकिन अगर मैं लिमिट
सर्किट यहां यूज करता तो लिमिट सर्किट उस
एंप्लीट्यूड वेरिएशंस ड्यू टू एरर उसको वो
एब्जॉर्ब कर लेता है और आ आउटपुट पे उसकी
रिफ्लेक्शन दिखाई नहीं देती यानी आउटपुट
पर जो मॉडले इि सिग्नल हमें मिलेगा उसमें
कोई फ्लक्स एशन नहीं होगा उसमें कोई एरर
नहीं होगा सो दिस इज ऑल अबाउट फोस्टर सिले
डिस्क्रिमिनेटर नेक्स्ट जो वीडियो होगा
उसमें हम रेशो डिस्क्रिमिनेट्स के बारे
में इन डिटेल डिस्कस करेंगे दिस इज द एंड
ऑफ द वीडियो थैंक यू सो मच फॉर वाचिंग दिस
वीडियो
Voir Plus de Vidéos Connexes
Phase Locked Loop(PLL) for 3 phase grid connected inverter | MATLAB Simulation.
Circuit Analysis Using Fourier Series ⭐ RL Circuit Response - Nonsinusoidal Waveform ⭐ Example 1
Kỷ thuật phát sóng SSB - P3: Diễn biến của tín hiệu âm tần, trung tần, và cao tần
Three Phase Rectifiers 1# Half Wave Rectifiers with Resistive Loads
5 Formulas Electricians Should Have Memorized!
Generated Adversarial Network
5.0 / 5 (0 votes)