Easiest DIY Motion Controller for FPV using Betaflight

Summary

在这个视频中，John展示了如何使用Radio Master mt12遥控器和Betterlight飞行控制器，通过自定义编程实现使用头部追踪器控制无人机飞行。他详细解释了连接和设置过程，并分享了在模拟器和实际飞行中的体验。John强调了这种控制方式在FPV飞行中的优势，尤其是在使用FPV翼时的自然感。此外，他还提供了关于如何更新固件、配置遥控器和飞行控制器的详细指导。

Takeaways

• 🚀 视频展示了如何使用Radio Master表面无线电遥控器和Betterlight飞行控制器通过特殊设置来飞行FPV无人机和翼型飞机。
• 🛠️ 作者通过自己动手改装，将Radio Master mt12遥控器与Betterlight飞行控制器相结合，实现了使用遥控器进行无人机飞行控制。
• 🔧 改装过程中，需要焊接五根线，包括电源、信号和重置按钮等，具体焊接方法和连接方式在视频中有详细说明。
• 🔄 需要更新遥控器的HTX固件至2.10版本，以支持使用串行训练器端口，并进行相应的设置。
• 📡 改装后的遥控器可以输出ASB信号，通过Betterlight开发者Steve的帮助，实现了这一功能。
• 🎮 作者强调了改装的风险，提醒观众在操作过程中要小心，并遵循所有安全指南。
• 🛫 改装后的遥控器可以用于无人机的Acro模式和翼型飞机的FPV飞行，提供了一种新的飞行体验。
• 🔄 在Betaflight配置器中，需要加载特殊版本的固件，并进行特定的设置，以启用头追踪器功能。
• 🔢 需要在HTX中设置串行训练器端口，并在模型设置中进行频道和混控的配置。
• 👍 视频展示了改装后的遥控器在实际飞行中的应用，包括单手飞行和模拟器练习。
• 👏 作者对支持者表示感谢，并鼓励观众订阅和支持他的频道，同时提醒观众注意飞行安全和遵守当地法规。

Q & A

视频中John是如何检查电池是否充满电的？

视频中并没有具体提到John是如何检查电池是否充满电的，只是提到了他等待这一天很久了，可能是在准备飞行前检查电池。

John为什么要清洗他的车？

John清洗他的车是因为他计划使用Radio Master遥控器来飞actra无人机和翼型飞机，他想为这一天做好准备。

视频中提到的Radio Master遥控器有什么特别之处？

Radio Master遥控器特别之处在于它内置了Express LRS，可以实现超长距离的遥控操作。

John是如何将Radio Master遥控器与betterlight飞行控制器连接的？

John通过焊接五根线将Radio Master遥控器与betterlight飞行控制器连接，并使用特殊版本的betaflight固件来实现连接和设置。

为什么John选择使用betterlight飞行控制器？

John选择使用betterlight飞行控制器是因为它已经具备了所需的大部分功能，只是缺少ASB输出，而且开发者Steve对这个项目很感兴趣，并帮助实现了所需的功能。

视频中提到的“头追踪器”或“无线电追踪器”是什么？

这些追踪器是用来检测和传递遥控器（或头戴设备）的方向和姿态信息给飞行控制器，以便实现更加直观和协调的飞行控制。

John在视频中提到了哪些飞行模式？

John提到了angle模式和acro模式，这两种模式都可以使用遥控器来实现更加直观和有趣的飞行体验。

如何使用模拟器来练习飞行？

John提到可以将遥控器连接到模拟器，如veloc drone，通过模拟器来练习飞行，这样可以在不实际操作无人机的情况下熟悉飞行操作。

视频中提到的“一键重置轴”功能是如何工作的？

“一键重置轴”功能允许用户通过按下一个按钮来告诉飞行控制器当前的姿态是零点，这样在飞行前可以校准遥控器的姿态，避免因姿态偏差导致的飞行问题。

John在视频中提到了哪些安全注意事项？

John提醒观众在操作时要注意安全，如果操作不当可能会导致遥控器或飞行控制器损坏，同时还要遵守当地的飞行规定，避免在人、动物和车辆上空飞行。

如何更新Radio Master遥控器的固件？

需要先更新遥控器的HTX软件到2.10版本，然后通过betaflight配置器加载特殊版本的betaflight固件，并按照视频描述的步骤进行焊接和设置。

Outlines

00:00

🎮 无线电遥控与无人机飞行控制系统的结合

John介绍了如何将无线电遥控与无人机飞行控制系统相结合，使用Radio Master表面无线电和Betterlight飞行控制器。他通过与Betterlight开发者Steve合作，实现了ASB输出功能，使得使用无线电进行无人机飞行成为可能。他还分享了使用Tiny woop DJI开放竞赛角度模式和Acro模式的体验，以及如何通过模拟器进行练习。此外，John还提到了使用这种设置在无人机竞赛中的优势，以及如何通过更新固件和设置来实现这一功能。

05:01

🔧 无线电与飞行控制器的硬件连接和配置

本段详细描述了如何将无线电与飞行控制器硬件连接，包括焊接五根线到飞行控制器，并解释了如何找到5V电源引脚。John还提到了使用不同电源引脚的选项，以及如何通过HTX 2.10版本进行配置，包括打开串行训练端口和设置模型。他还强调了在连接之前确保无线电和飞行控制器正确校准的重要性，并提供了详细的步骤和注意事项。

10:02

🛠 配置Betaflight和HTX设置

在这一段中，John指导观众如何在Betaflight配置器中更新固件，启用专家模式，并选择特定的固件版本以支持ASB协议。他还解释了如何设置头追踪器参数，包括最大角度和资源重映射。此外，John还提供了在HTX中设置训练器端口和模型的具体步骤，包括如何设置通道顺序和调整节流阀的偏移量。

15:03

🚀 实际飞行测试与安全提示

John分享了实际飞行测试的经验，强调了在飞行前进行充分校准和测试的重要性。他提醒观众在飞行时要注意安全，遵守当地法规，并在飞行前正确设置无线电。此外，他还提到了如何使用HTX进行模型设置，以及如何通过监视通道条来验证系统是否正常工作。最后，John提供了购买无线电的链接，并鼓励观众订阅他的频道和支持他的Patreon。

🎉 视频结尾的总结与展望

视频的结尾部分，John总结了整个项目，并对未来的无人机飞行体验表示了乐观。他提到了这种新的飞行方式如何为初学者提供了更直观的学习路径，并且对现有无人机飞行方式进行了创新。此外，他还展示了一些无人机的维护和升级工作，以及对未来飞行体验的期待。

Keywords

💡无人机

无人机，即无人驾驶飞行器，是一种远程控制或自主飞行的航空器。在视频中，无人机是主要的讨论对象，尤其是用于竞速的小型无人机。例如，视频中提到了使用遥控器来控制无人机进行飞行。

💡遥控器

遥控器是一种无线设备，用于远程控制其他设备，如无人机或遥控车。视频中提到了Radio Master mt12这款特殊的遥控器，它内置了Express LRS系统，可以进行长距离控制。

💡FPV

FPV是“First Person View”的缩写，意为第一人称视角。在无人机飞行中，FPV允许飞行员通过无人机上的摄像头实时观看飞行画面。视频提到了使用遥控器进行FPV飞行，提供了一种身临其境的飞行体验。

💡校准

校准是指调整设备以确保其性能达到预期精度的过程。在视频中，校准用于确保遥控器和无人机的传感器正确同步，例如校准加速度计以保证飞行控制的准确性。

💡传感器

传感器是检测和响应物理条件变化的设备，如运动、温度或压力。视频中提到了使用加速度计和陀螺仪传感器来检测遥控器的倾斜和移动，从而控制无人机的飞行。

💡Betaflight

Betaflight是一个流行的无人机飞行控制器固件，用于自定义和优化无人机的飞行性能。视频中提到了Betaflight配置器，用于设置和调整无人机的飞行参数。

💡焊接

焊接是一种连接金属或其他材料的方法，通过高温使材料熔化并结合在一起。视频中的角色提到了焊接操作，将遥控器的信号线与飞行控制器连接，以实现自定义控制方案。

💡自定义

自定义指的是根据个人需求或偏好对产品或服务进行修改或调整。视频中展示了如何通过自定义遥控器和无人机的设置，实现使用遥控器进行无人机飞行控制的创新方法。

💡竞速模式

竞速模式是一种无人机飞行模式，通常用于无人机竞速比赛，要求无人机以高速进行飞行。视频中提到了在竞速模式下使用遥控器进行飞行，增加了飞行的趣味性和挑战性。

💡模拟器

模拟器是一种软件或设备，用于模仿现实世界的对象或系统，以供训练或测试。视频中的角色提到了使用模拟器来练习无人机飞行，这是一种安全且经济的学习方法。

💡风险

风险指的是可能发生的危险或损失。视频中提醒观众在进行自定义改装和飞行操作时要注意潜在的风险，比如焊接遥控器和飞行控制器时可能会损坏设备。

Highlights

使用Radio Master表面无线电控制，可以用于遥控汽车、船只等，并且具有Express LRS内置功能，可以实现超长距离控制。

通过与Betterlight飞行控制器配合，可以轻松实现无线电的头部追踪功能，无需复杂的编码和校准。

Radio Master mt12无线电具有特殊功能，可以用于FPV无人机和翼型飞机的飞行控制。

介绍了如何将无线电与Tiny woop DJI open race角度模式和Acro模式进行连接和设置，提供了直观的飞行体验。

使用无线电进行无人机飞行时，可以单手操作，另一只手可以进行其他任务，如录制视频。

展示了在模拟器中使用无线电进行无人机飞行的练习，强调了单手操作的优势。

讨论了女性飞行员在GQ排行榜上超越男性飞行员的情况，强调了飞行技术的性别无关性。

介绍了如何使用Betaflight配置器和特殊版本的Betaflight固件来设置无线电的头部追踪功能。

详细说明了如何焊接五根线到飞行控制器上，并强调了操作风险和安全措施。

提供了焊接图和说明，帮助用户理解如何将无线电与飞行控制器连接。

强调了在设置过程中，需要确保无线电和飞行控制器的陀螺仪正确校准。

介绍了如何在HTX中设置ASB训练器端口，并提供了详细的步骤和注意事项。

讨论了如何通过HTX设置模型，包括训练器模式、通道顺序和油门设置。

强调了在无线电上使用重置按钮的重要性，以确保飞行控制器在飞行前正确校准。

提供了关于如何安全地绑定无线电到飞行器，并进行飞行前检查的建议。

讨论了使用无线电进行FPV翼型飞机飞行的自然感受和飞行体验。

以幽默的方式结束了视频，展示了新一代无人机飞行员的成长和创新精神。

Transcripts

John here guys this is how you check if

your battery's

charged my what's up guys I've been

waiting for this day for so long I been

washing my car because today we're going

to be using these to fly actra drones

and the wing and this is Radio Master

surface radio with a special thing on

it but first let me call to my expert oh

my wing is doing that what's happening

what are you doing with my radio I'm a

motion

expert as a result of this video anyone

will be able to trick motion of his htx

radio with betterlight flight controller

because now it's so easy it's crazy

surface radio is remote control for

boring stuff like RC car boats and they

use these for throttle and these for

steering left and right radio Master

mt12 is a special one because it has

Express lrs built in and you can even do

this for crazy long range and ever since

radio Master released this remote I was

thinking I got to somehow fly with it

and I was like okay I can use these for

coordinated y en roll these for throttle

but then like I can install joystick

here for peach or I can use this for

peach that that's not very cool by the

way radio Master did not send me this

radio I bought it from my patreon money

and thanks a lot to all my supporters

but then I was like calm down I

can code and make a motion

tracker but are doing a standard

libraries are kind of slow and then you

need a code board alignment jar and

accelerometer calibration sounds

familiar wait a second betterlight has

all that already it is only missing ASB

output for your Peach and roll and then

this is just your head tracker or radio

tracker or your imaginary girlfriend

tracker so I reached to Mr Steve a

betterlight developer so that he taught

me how to make betterlight code to

Output sbas not just receive ASB and he

loved this idea so much he just went

ahead and made it work I almost didn't

have to code anything but my role was

still very

important hey Steve what code faster

faster

[Music]

FAS I'm going to explain how to connect

and set it up you can use the timeline

but it's pretty easy it's just three

wires here two wires here and you done

but I want to emphasize that this works

way better than I thought I have it

connected to Tiny woop DJI open race

angle mode is so intuitive it's just

your Peach and roll and Acro mode is all

the same just more fun and you can even

plug in your radio in the simulator like

veloc drone let's just practice there

look I'm flying with one hand while

recording a stick cam with another hand

using only one hand for drone racing is

a big Advantage because your other hand

can do anything you want while you're

flying a

drone arm up

go whoa what what the video video

all right pus arm him up

go Mr Dave this is emergency what kie

somehow beat my time in the GQ

leaderboard and I think this is the

first female that ever been HED than me

on the leaderboard oh my goodness and uh

well let's call K and see what she says

how she did she do that

hello K FV 101 I guess it's just cuz I'm

better all right she just said I'm

worthless you pilot we've been

flying this motion radio literally 2

days non-stop so much fun oh maybe this

the only way met can freestyle but the

coolest experience is to fly your fpv

wing there's no y to worry about but

then you're like a Jet Pilot except with

a throttle on the radio can't believe

you made this oh of course it is

not going to replace my sticks for the

Drone racing but honestly for the wing I

don't even want to go back to my normal

radio launching is a little hard because

as you do it your hands are kind of

moving around you just need a watch for

that but it's just so natural to fly it

in fpv all right you need betaflight

flight controller I'm using Fox here

f722 20 X20 that was just laying on my

table by the way you're doing everything

here at your own risk if you burn your

radio or anything that's not on me you

can blame Cole because he's playing

video games instead of flying drones so

we will need to solder five wires total

and ideally if you just can find two

separate URS two separate ground and

this 5v4 pin which is actually 4v5 if

your flight controller doesn't have it

marked you can actually find it by

plugging in USB in the flight controller

and then with a multimeter checking

which 5vt pod is being powered from USB

in my case it was this 5V P it means

that most likely your flight controller

can be powered up from this 5vt pin if

you provide 5 volts most likely if

you're scared you can power up your

flight controller using this VCC pin and

providing some small I don't know 2s

battery and then you don't need to

solder this for 5 Pin that's actually a

good idea because then you can just

depower your flight controller when you

don't use it on your radio anyway I

decided to take a risk and uh this is my

soldering diagram these three or two

wires are going into your radio into

serial trainer port and this is how your

radio will know its orientation and

passes it over to your flying craft so

in this case if you solder this red wire

then your flight controller will be

powered up from your radio another good

idea that I was too lazy to do is that

right here you can solder like a

separate switch to turn on and off your

flight controller it might be all right

but every time I plug in USB into my

flight controller on the radio it also

tries to power like the whole radio and

the radio really don't like it anyways I

miss all the precaution steps and I'm

still alive so it's whatever you decide

to do pay attention the TX from the

flight controller goes to RX on the

radio as always here at the bottom you

can see a weird connection tx5 goes to

the ground through the button and they

are connected when the button is pressed

you need this button to reset your axis

when you ready to reset your axis Ivon

you're making a lot of sense right now

if you ever had to deal with head

trackers then you know what's happening

with Y imagine you're preparing to fly

you're walking with your radio around

then you sit down and of course your y

will be crazy because radio will think

that your Y is like pointing somewhere

else so you push this button to tell to

the flight controller that like this is

my zero yo the current yo is now zero

make it happen and flight controller

will be like okay okay I remember now

that this direction is zero yard this is

type of a button that I was using it's

very little you just need to figure out

which pins are connected when you're

pushing this button and solder them up

according to this diagram and then you

can double s tape this button anywhere

in your radio where it's accessible on

mt12 remote the serial Ard Port is

inside but it's not too bad you don't

have to take apart the whole radio but

before you open up your radio you need

to update htx to 2.10 cuz in previous

versions you cannot use that serial port

and my radio came with 2.10 but with a

development beat and it also didn't

support it so anyways update your radio

to 2.10 htx then just these two screws

pull carefully this wheel unplug its

ribbon cable and the plug will be right

there I you can read it I don't know why

I'm reading it for you this is my poor

photo of that plug you probably need

like a twizz to get close to it and you

can see here well you can't but there is

a ground from this side then there is TX

then there is rx which we don't use and

then there's 5vt pin I think the name of

this connector is 1 mm GST I'm I'm not

sure actually but it's the same as

foxier Predator is using and that's

where I got it from this is a four pin

connector if your connector is like 567

or eight pins you can just cut the

Plastics with the scissors so that it's

only four pins just absolutely make sure

that you're following this diagram don't

connect 5vt to TX that's probably not

going to be good for your

radio if you decide to use tx16s radio

for example then you don't even need to

open it up because there are two yard

ports at the bottom you can just use

them now let's get to flashing special

version of betaf flight on this flight

controller hopefully it's not going to

burn your when you plug in with USB

in your flight controller for now open

11.0 betaflight configurator go to

update firmware then enable expert mode

then click Show release candidates here

select development then autod detect

your flight controller and right here

you need to select

450 CAC after that scroll a little bit

down and select ASB in the radio

protocol and then in the select commit

or pull request not in the custom

defines right here on the right side you

need to type tracker with the capital

letters and then hit enter then it

should look like this see it says

tracker then click load firmware online

you might wait a little bit until Cloud

builds it and then you see there will be

like show log for double verification

you can click this show log in this log

you can scroll a little bit down until

you and then you should see something

like pragma message FC version string

450 tracker one means you good most

likely and then you just click flash FW

and you can ignore the risk if you

decide to ignore the risk no hopefully

in the near future is going to be in 4.6

so maybe you won't have to use this

weird flashing procedure or for now you

can Flash from Mr Steve's pull request

the link will also be in the description

if it's going to be merged in 4.6

probably some setup procedures will be

changed so you'd better really read

these noes now we're dealing with the

Leading Edge of the unreleased

technology then click connect this

message is fine then go to Port stop and

make sure that nothing selected here

except the very first line I guess you

cannot unselect it anyways but you don't

need any of this then go to setup

page and click calibrate accelerometer I

forgot to tell you that at this point

your flight controller should be sticky

taped to your radio already like then

you should absolutely double check that

when you turn your radio on all three

axes the 3D picture on the setup page

repeating everything you doing with your

radio if something is off just like with

a normal drone go to configuration page

and then there is board and sensor

alignment and you can adjust these

values it means you mounted your flight

controller like upside down or like 90°

rotated on your radio all the next steps

are on the C tab it's at the very bottom

on the left side now we need to set up

your pins we need to tell BF flight

where you sold your garbage to and for

that you need this diagram your diagram

could be a little bit different if

you're using different flight

controllers or different pins but you

should absolutely know that I solded my

radio to tx1 and then my button on tx5

like that's my my case your case figure

it out all the following Commandments

will be in the description of this video

so it was easier for you to copy and

paste although it's not exactly copy

paste you kind of need to think a little

bit the first magic command is this

we're telling to BTA flight that serial

Port zero will be used to Output sbas do

remember I soldered it to tx1 but

programmer starts counting from zero

that's why here is zero if you solded it

to let's say tx9 then here you will have

to put eight it's like minus one don't

mix it with this zero leave this zero

alone then hit enter then you need to

tell to bet flight where did you solder

your button and for that we need to do

some resource remapping I soldered my

button to tx5 so now I have to just

remember tx5 and in this case it's not

like minus one it will be tx5 so type

resource and then it lists all the

resources in this list I need to find

serial tx5 because that's where I solder

my button to whatever you need to find

if I know in front of Serial tx5 I

have 12 I need to remember this number

then I need a free serial tx5 resource

that's pretty easy you just copy this

line paste it right here and instead of

C12 you just type none and press enter

Then I need to assign your reset

resource to C12 that's also pretty easy

you just type resource head tracker 1

C12 hit enter Then you type set head

tracker your shimi enable off this is

the feature for the actual head tracker

on your head so that you could reset

your by shaking your head a little bit

we don't need it on the radio so we're

turning it off hit enter then you need

to type set head tracker Max angle 30

instead of 30 you can decide to put 45

whatever you need this will be your

maximum angles that corresponds to your

maximum so-called stick command so I use

30° maybe you want to start with 45°

depending on like how shake your hands

are if I put here 30 it means 30° angle

on any of the axes will give these AIS

like full command well probably 45 is a

good start but I kind of like 30 it's

less Precision but faster hit enter and

then type save and enter again and we're

done now you should unplug your flight

controller and power up your radio

hopefully it's not going to burn now we

just got to do a few tweaks in the htx

if you already know how to set up as bu

trainer Port then you're pretty much

done get the out of here I didn't

know so big thanks to htx developers in

the htx Discord for helping me with that

go to system Hardware settings and some

at the bottom you should see ox1 and you

should set it to esbas trainer some

radios right here even allow to turn on

and off its power mine don't so it's

whatever then make a new model you can

name it like I'm going to burn my

in the model settings on the setup page

find trainer and set mode to master

cereal I like cereal then go to mixes

and you can set up any channel order you

need this is my screen trainer one tier

one will always be roll tier two will be

Peach and tier three will be ya and you

see I assigned tier one to channel one

tier two to channel two and tier three

to channel four and that's kind of a

standard unless you're fanking keys or

if you are nail throttle is a little bit

more tricky on this surface radio you

see it says weight 200 and if we go

inside of a throttle that's how I have

it set it up I had to put weight 200 and

offset minus 100 the reason for that is

that this throttle has a spring inside

and it can go both ways I didn't want to

use this so this is my zero throttle and

this is my full throttle and this is my

50% throttle and this is my zero

throttle after that power cycle radio go

to channels Monitor and then you should

be able to see these three bars are

moving as you moving your radio around

and then throttle moving from - 100 to

Plus 100 as you pushing that button

another thing to remember when you power

up your radio with a flight controller

you got to put it on the table and let

it steal for a few seconds just like the

normal drone so that it calibrates it

gyro now you need to bind this radio to

your aircraft verify that everything

works like you normally verify and be

extra extra extra careful you're by

yourself follow local regulations don't

fly over people dogs and cars and

whatever you'll probably also need to

set up like these switches for like

arming angle mode like turtle mode

whatever you want to do and you must

remember about your reset button right

before you arm it so you hold your

remote flat and forward reset your and

then arm don't do this like all right

I'm holding it flat let me reset your

and then let me try to arm it no so any

your movement after you reset your you

turn your radio like this you arm it and

your quad will freak out don't move your

unless you want your quad to move your

and if you arm your quad while you're

ready with tilted back your quad will

pit back right away and if you did

shitty soldering and this thing

disconnects FG fly who knows what's

going to happen let us know in the

comments another good verification go to

Channel's Monitor and especially watch

your channel bar it should not drift at

all if your radio is still on the table

could be like 1% a minute max if it's

moving faster than you did not let it

calibrate gyro pretty good or your

flight controller is garbage you can

also like put it on the table reset your

then move your radio around on all AES

and then put it on the same place and

then your should be approximately around

zero that all sounds complicated but if

you already know like betaflight htx

andpress rest then it's really a piece

of cake if you want to buy this radio

please check out affiliate Link in the

description of this video These Are

Johnny Five affiliate links he almost

burned his

eyebrows that was way crazier than I

thought it was going to be guys thank

you very much for watching please as

always consider subscribe to my lazy

patreon the link in the description I

forgot to tell to like the video does it

mean it's nobody going to like it or

nobody going to like like me anymore

check out behind the scene at the very

end of the video and see you in the next

one if I'm not

[Music]

lazy you can see the riding on the

pavement young kids that growing up in

basement online a whole new generation

I'mma make mine so you better go take it

old way they need a new replacement

decentralized can't contain it we're

changing lives yeah GR in call it to a

side of the older generation keep you up

and night yeah make all the demons Qui

yeah we were built a drive yeah I think

that we've all enough keep you up and ey

yeah make all the demons quiet yeah we

were built to thrive yeah I think that

we' all let it know yeah I think that

we've all at it know s the with the old

they know that we're calling the

blood you got me like oh yeah I think

that we've all let it know

SI dealing with the old plan they know

that we're calling their

BL hey it's too late to try to go

contain it a generation fueled by

creation we live lives on a small screen

Nation we control the airwaves no

negotiation I refuse to think we need

saving something good will come from

creation and when we think that the

world is too anxious we'll adapt to all

survive and save it keep you up and ey

yeah make all the demons Qui yeah we

were built a Thrive yeah I think that

we've all had enough keeps you up and

eye yeah make all the demons Qui yeah we

were built to thrive yeah I think that

we all let it know yeah I think that we

all let it

[Music]

know can do anything you want while

you're flying a

drone Mr Matt what did you mean by that

uh nothing nothing no uh just uh

celebrating liveos all right Mr Hiro as

a actual Jet Pilot do you approve this

radio yes it's fun actually there's a

nice uh Sparks

RC what the heck what's up guys I am so

excited about this days been waiting for

it for so long no it's actually really

exciting it's uh it's nice it's very

easy also for people that are new to

Flying this could be a a much easier

path to get you don't have to learn

which sck is which this is kind of ation

between your left and right and all that

so this is way way more intuitive DAV is

shocked right

there so my wing was on cost and now I

need to like build it with exal r and

separate VTX and that kind of suck look

at my Professional Cable Management

oh God

[Applause]