Toyota Camry Rear Brake Pad Replacement With Electronic Brake 2018 - 2023

Friendly Mechanic
20 Nov 202309:40

Summary

TLDRIn this instructional video, the host guides viewers through the process of replacing the rear brake pads on a 2020 Toyota Camry. The tutorial begins with entering service mode for the rear electronic parking brake, followed by safety tips on using jack stands. The host demonstrates removing lug nuts, lifting the vehicle, and accessing the brake caliper. Two methods for retracting the brake piston are shown, and the importance of preserving the dust boot is highlighted. The video concludes with brake pad assembly and installation, emphasizing the correct positioning of pads and clips, and finally, exiting service mode. The host encourages viewers to subscribe for more helpful content.

Takeaways

  • πŸš— Start by putting the 2020 Toyota Camry into service mode for the rear electronic parking brake by turning on the ignition, releasing the parking brake, and performing a specific sequence of brake pedal presses and releases.
  • πŸ› οΈ Use an electronic impact driver to remove lug nuts, but a regular tool is fine if you don't have one; ensure to loosen all nuts before lifting the vehicle.
  • ⚠️ Always use jack stands when lifting the vehicle for safety and never rely solely on a jack.
  • πŸ”© A 14 mm hex socket and a 17 mm skinny wrench are needed to remove the brake caliper assembly.
  • πŸ”§ Hold the caliper assembly in place with pliers or a vice grip to prevent damage to the rubber seal while loosening the bolts.
  • πŸ”„ When removing the top bolt, leave a few threads to prevent the bracket from moving when removing the bottom bolt.
  • πŸ”§ Retract the brake caliper piston using either the old brake pad or a flathead screwdriver to push it back into place.
  • πŸ›‘οΈ Inspect the dust boot and ensure it is intact; if damaged, fold it back carefully without puncturing it.
  • πŸ”¨ Remove the old brake pads by hand or with a flathead screwdriver if necessary.
  • πŸ”© Assemble the new brake pads with the provided shim kit and brake pad kit, ensuring correct placement and clip attachment.
  • πŸ”§ After installation, start the vehicle and remove service mode by holding the brake pedal with the button blinking for 5 seconds.

Q & A

  • What is the main topic of the video?

    -The video is about replacing the rear brake pads on a 2020 Toyota Camry.

  • What is the first step to put the vehicle into service mode for the rear electronic parking brake?

    -The first step is to turn on the ignition, put your foot on the brake, release the parking brake, and then turn off the ignition.

  • How do you activate the service mode for the rear brake system?

    -You activate the service mode by turning the ignition back on, putting your foot on the brake, and raising and lowering it three times within 8 seconds. Then press and hold the brake until you hear the rear brake electronic motor wind back.

  • What tool is recommended for removing the lug nuts?

    -An electronic impact driver is recommended for removing the lug nuts, but it's not mandatory as other tools can be used if unavailable.

  • Why is it important to use jack stands when lifting the vehicle?

    -Using jack stands is crucial for safety as it ensures the vehicle is securely held up and not just relying on the lifting device, preventing any potential accidents or damage.

  • What size hex socket is needed to remove the brake caliper?

    -A 14 mm hex socket is needed to remove the brake caliper.

  • How do you prevent the brake caliper from spinning while loosening it?

    -You need to hold the T part of the nut with a skinny wrench or pliers to prevent it from spinning.

  • What are the two methods shown in the video for pushing the piston back into the caliper?

    -One method is using the old brake pad to retract the piston back into place, and the other is using a flathead to pry back the brake pad and then push the piston back.

  • What should you do if the dust boot of the brake pad is damaged?

    -If the dust boot is damaged, you should fold it back in carefully without puncturing it, restoring it to its original position.

  • How do you assemble the new brake pads according to the video?

    -You assemble the brake pads by piecing together the brass and silver looking parts with clips, placing them on the brake pad, and ensuring they fit correctly in the slots.

  • How do you exit the service mode after completing the brake replacement?

    -To exit the service mode, turn on the ignition with your foot on the brake, and while the button is blinking, hold it for 5 seconds.

Outlines

plate

This section is available to paid users only. Please upgrade to access this part.

Upgrade Now

Mindmap

plate

This section is available to paid users only. Please upgrade to access this part.

Upgrade Now

Keywords

plate

This section is available to paid users only. Please upgrade to access this part.

Upgrade Now

Highlights

plate

This section is available to paid users only. Please upgrade to access this part.

Upgrade Now

Transcripts

plate

This section is available to paid users only. Please upgrade to access this part.

Upgrade Now
Rate This
β˜…
β˜…
β˜…
β˜…
β˜…

5.0 / 5 (0 votes)

Related Tags
Brake PadsToyota CamryCar RepairDIYService ModeElectronic Parking BrakeLug NutsCaliperPistonSafety Tips