What glue is best for your camera leatherette? Testing some suggested adhesives for camera repair!

Summary

このビデオでは、レトロカメラのレザーエットを再接着するための接着剤の選び方について解説しています。修理に必要な接着剤は、接着後も動かすことができる柔軟性と、長期間持続する強さが必要です。また、カメラの修理や分解を容易にするために、接着剤は除去可能でなければなりません。様々な接着剤を実際に試し、その強さと除去のしやすさを比較しています。結果として、E6000やダブルサイトテープが最適な選択肢として勧められています。

Takeaways

• 📷 スクリプトは、レトロカメラのレザーエットを貼り直すための接着剤について話しています。
• 🔍 作者は、ネット上の意見を集めて、実際に11種類の接着剤をテストすることを計画しています。
• 🛠 接着剤は、接着後に移動可能で、長期間しっかり貼り付く必要があります。また、レザーエットやカメラを傷つけず、いつでも剥がせる性質が必要です。
• 🔬 作者は、メーカーの指示に従って、またはそれに反して接着剤をテストし、どちらが最良の結果を出すかを検証します。
• 🐵 テストに使われる素材はアルミニウムと、ブロニカS2Aのクロムメッキされた不銅鋼ボディで、非多孔性金属として同様の目的を果たすと述べています。
• 👨‍🔧 テストに用いた接着剤には、ゴリラ接着剤、接着剤、スーパーグル、エルマーズPVA接着剤、スプレー接着剤、ボスティック接着剤、E6000、ユーフロ接着剤、両面テープなどがあります。
• 🚫 スーパーグルはレザーエットに悪影響を与える可能性があり、使用しないことを勧めています。
• 👍 E6000は、接着力が強く、クリーニングが容易で、クリアで粘着性のある特性を持っており、良い結果を出したと評価されています。
• 🔄 両面テープは、接着が容易で、再貼り付けが可能で、カメラから剥がしやすく、作者が最も満足している接着方法の一つだと述べています。
• 🔑 最も重要なのは、接着剤が作者の要件を満たすことで、接着がしっかりしていて、剥がしやすさを保ち、カメラやレザーエットを傷つけないことです。
• 📝 作者は、コメント欄で異なる意見があることを理解しており、最適な接着剤は個人のニーズに応じて異なるかもしれないと述べています。

Q & A

ビデオで紹介されたのはどのカメラのモデルですか？

ビデオで紹介されたカメラモデルはBronica S2Aです。

ビデオの主題は何についてですか？

ビデオの主題は、古いカメラのレザーエットを剥がれたり貼り直しが必要な場合にどの接着剤を使うかについてです。

接着剤を選ぶ際の重要なポイントは何ですか？

接着剤を選ぶ際の重要なポイントは、接着剤が接着した後もカメラやレザーエットを傷つけず、数年間しっかり接着し続ける能力があること、また必要に応じて接着剤を剥がすことができることです。

ビデオで試した接着剤は何種類ありますか？

ビデオでは11種類の接着剤を試しました。

ビデオで使用した接着剤のテスト方法は何ですか？

ビデオではメーカーの指示に従った方法と、それに従わない方法で接着剤をテストしました。その後、接着剤の接着力を確認し、24時間以上経過した後に接着剤を剥がしてみました。

ビデオで試した接着剤の中で、最も適切だと思われる接着剤は何ですか？

ビデオの結果から、最も適切だと思われる接着剤はE6000とダブルサイドテープのようです。

ビデオで使用した接着剤のどれが最悪の結果だったと述べられていますか？

ビデオで述べられた最悪の結果はスーパーグルです。それはレザーを破壊し、接着力を高める代わりに不良な影響を与えたと報告されています。

ビデオで使用した接着剤の中で、接着力を高めずに簡単に剥がせる接着剤は何ですか？

ビデオで使用した接着剤の中で、接着力を高めずに簡単に剥がせる接着剤はエルマーのPVA接着剤や強力PVA接着剤が挙げられます。

スクリプトの内容に基づいて、どのような接着剤がカメラのレザーエットに適しているかを示す実験が行われましたか？

ビデオでは、メーカーの指示に従い、またそれに従わない方法で、11種類の接着剤を試し、それぞれの接着力を比較して、カメラのレザーエットに適した接着剤を探求しました。

ビデオで使用した接着剤のどれが最も簡単に剥がせることができたと述べられていますか？

ビデオで述べられた最も簡単に剥がせた接着剤はダブルサイドテープのようです。

ビデオの最後に、カメラのレザーエットを貼り直す際に勧められる接着剤は何ですか？

ビデオの最後に勧められた接着剤はE6000とダブルサイドテープです。これらの接着剤は接着力が高く、必要な時に簡単に剥がすことができるという利点があります。

Outlines

00:00

📷 レトロカメラのレザーカバーの接着

ビデオでは、レトロカメラのレザーカバーの再接着について説明しています。特に、ブロニカS2Aのレザーカバーが剥がれ始めたため、新たにレザーを貼り替えることにしました。接着剤を選ぶ際には、接着後も動かすことができる柔軟性と、長期間持続する強さ、レザーやカメラに傷をつけない性、また必要に応じて剥がせることが求められます。plyo bondという接着剤が製造業者で使用されているとされていますが、英国では入手困難であるため、手元にある様々な接着剤を試してみることにしました。

05:01

🔍 接着剤の比較実験

11種類の接着剤を比較実験し、それぞれ製造業者の指示に従った方法とそうでない方法で試しました。アルミニウム板を使ってテストを行い、接着剤を均等に塗布し、接着力を比較しました。ゴリラ接着剤やコンタクト接着剤、スーパーグル、PVA接着剤、スプレー接着剤、ダブルサイドテープなど多岐にわたる接着剤を試し、接着力と剥がしやすさを評価しました。

10:04

🏆 接着剤の実験結果

実験結果を評価し、接着剤の適切さを判断しました。スーパーグルはレザーに悪影響を与える一方で、PVA接着剤は接着力が十分ではなかったため、これらの使用は避けるべきだと結論づけました。一方、e6000やBostikの接着剤は接着力が強固で、剥がしやすさをも保ちました。ダブルサイドテープは、接着が均一で、剥がしやすく、清潔に剥がせることができたため、特に優れた結果を示しました。

15:07

👍 おすすめの接着剤

最終的にダブルサイドテープとe6000接着剤が最適な選択であると判断しました。これらの接着剤は接着力が強固でありながらも、必要な時には簡単に剥がすことができるという利便性を持っています。他の接着剤と比較して、特にダブルサイドテープは事前に接着剤を貼り、均一な接着を確保し、剥がしやすさを兼ね備えているという利点があります。このビデオはカメラのレザーカバーの接着に関する参考になるでしょう。

Keywords

💡レザーエット

「レザーエット」とは、カメラなどの機器の表面に貼り付ける、革のような素材のことで、視覚的な美しさや握りやすさを提供します。このビデオでは、レトロカメラのレザーエットが剥がれ始めたため、修理のために取り外し、新しいレザーエットに置き換えるプロセスが説明されています。

💡接着剤

「接着剤」とは、物同士を結びつけるために使われる材料のことで、ビデオではレトロカメラのレザーエットを再貼り付けるために何種類かの接着剤が試されています。接着剤の選択は、修理の質と耐久性に大きな影響を与えるため、ビデオの核心的なトピックの一つです。

💡ブロニカS2A

「ブロニカS2A」は、ビデオで使用されるレトロカメラのモデル名です。このカメラのレザーエットが剥がれ始めたため、修理の対象となっています。カメラのモデル名は、ビデオの具体的な修理対象を特定する上で重要なキーワードです。

💡接着条件

「接着条件」とは、接着剤を適切に動作させるために必要な条件のことで、ビデオでは接着剤を適用した後、一定時間干燥させたり、適切な強度で貼り付ける必要があることが強調されています。これは、接着剤の性能を最大限に引き出すために重要な要素です。

💡テスト

「テスト」とは、ビデオで行われる接着剤の性能を評価するための実験的なプロセスで、異なる接着剤を適用し、どれが最も適切かつ効果的であるかを判断します。ビデオでは11種類の接着剤がテストされ、その結果が修理の最適な方法を決定する上で役立ちます。

💡プライヤーボンド

「プライヤーボンド」とは、ビデオで言及される製造者が使用する接着剤の種類の一つで、接着力が強く、長期間持続するという特性があります。しかし、ビデオのナタでは特定の「プライヤーボンド」という製品を見つけることができず、代わりに類似の接着剤をテストしています。

💡接着力

「接着力」とは、接着剤が物質を結びつける力の強さのことで、ビデオでは接着剤の接着力をテストし、最も適切な接着剤を選ぶために比較しています。接着力は、カメラのレザーエットの修理品質に直接関係しています。

💡除去可能性

「除去可能性」とは、接着剤で貼り付けられた物が必要な時に簡単に剥がせる性質のことで、ビデオでは修理や部品交換のためにカメラのレザーエットを再び取り外す必要があるため、この特性が重要です。

💡ダブルサイトテープ

「ダブルサイトテープ」とは、ビデオでテストされた接着剤の種類の一つで、両面に接着剤が塗られたテープで、簡単に貼り付けと除去が可能な特性があります。ビデオの結果から、このテープは修理プロセスで優れた性能を示しました。

💡E6000

「E6000」はビデオでテストされ、優れた接着力を示した接着剤の一つで、特に透明性と接着後の残り粘着力のバランスが良く、カメラのレザーエット修理に適した選択肢として示唆されています。

Highlights

Introduction to the topic of using glue to re-stick leatherette on vintage cameras.

The presenter's own Bronica S2A camera is being used as a test subject for the glue experiment.

Leatherette on vintage cameras often peels away and needs re-gluing.

Different types of glue have been suggested online for re-stick leatherette.

The glue needs to be specific for the task, allowing for movement and long-term adhesion without damaging the leatherette or camera.

Plyo bond is mentioned as the manufacturer's choice, but it's hard to find.

Contact adhesives are being tested as alternatives to Plyo bond.

Eleven different types of glue are tested in various ways.

Aluminium and chrome-plated stainless steel are used as materials for testing adhesives.

Gorilla Glue is tested both according to and not according to manufacturer's instructions.

Super Glue is tested and found to damage the leatherette.

Elmer's School PVA Glue and Strong PVA are tested for their adhesive properties.

Spray adhesive and Bostic Contact Adhesive are tested for their tackiness and bond strength.

E6000 is tested as a recommended adhesive for its clarity and bond strength.

Double-sided tapes are tested for ease of application and removal.

Results are shared after a week for a thorough assessment of the adhesives' performance.

Gorilla Glue, when not applied according to instructions, forms a very strong bond.

Super Glue is not recommended due to its damaging effects on the leatherette.

PVA adhesives are found to be not strong enough for the task.

Spray adhesive and Bostic Contact Adhesive are too strong and damage the leatherette.

E6000 provides a good strong bond that is also removable without damaging the leatherette.

Double-sided tapes, particularly the Tesa brand, show promise for easy application and clean removal.

The presenter emphasizes the importance of choosing an adhesive that meets specific needs for the task.

The video concludes with a summary of the most suitable adhesives for re-sticking leatherette on vintage cameras.

Transcripts

[Music]

good evening everybody welcome back to

the 120s

today we're out in the workshop and we

are talking about glue

specifically what glue to use to stick

down or re-stick down

the leatherette on your vintage cameras

this is my trusty bronica s2a

um and as you can see it's uh the the

leatherette is really starting to peel

away in a few places

so i'm planning to re-skin this all

together i'm planning to get rid of this

old leatherette

um and replace it with a whole new one

so

for that i've been trying to work out

what is the right

glue to use to stick down the new

leather app

and it seems to be something of a bone

of contention um

there seem to be a hundred different

opinions around the internet about what

is the right glue to use

so i figured the best thing i could do

is take all of those suggestions

everything that people online have

suggested be used

uh and test it all now the glue that you

use to stick down

a leatherette actually needs to be quite

specific because there's certain jobs

that it needs to do

number one is that when you put the

leather when you when you apply the glue

put the leather onto the body it kind of

needs to be

movable for a short period of time to

make sure you can get it fully lined up

whatever glue you use also needs to be

it needs to hold firm for several years

it needs to not destroy the leatherette

it needs to not destroy the camera but

it also needs to be removable

you need to be able to take the leather

off again at some point

because invariably almost all cameras

are hiding stuff

underneath the leatherette usually a lot

of screws that you need to

to get at to dismantle the camera are

covered by the leatherette

and therefore you want it to stay on

but you also want to come off when you

wanted to

plyo bond is generally accepted to be

what the manufacturers use um

you can't get i can't i certainly can't

find anything

they're specifically called plyo bond

here in the uk

uh but as i understand it player bond is

a type of contact adhesive

so i've got hold of several different

contact adhesives on pretty much

everything i can get my hands on

i'm going to try them all i'm going to

try them in a few different ways

according to manufacturer's instructions

and we'll try it not according to

manufacturer's instructions and see

which one works best

so here we go i actually have 11

different types of glue that i'm going

to test today

this is the material i plan to be using

quite like it

i have a strip of aluminium

which i normally use to cut lens boards

from now

the body of the s2a is chrome plated

stainless steel so

it's not exactly the same but it's a

non-porous metal

so it should serve the same purpose for

now so we'll start with the

gorilla glue all right then so i'm going

to do as the manufacturer suggests

apply to both sides so spread

fairly evenly across there and spread

across aluminium aluminum

i should say we'll leave that to dry a

bit

and in fact the next one i'm going to do

uh is

the same thing contact adhesive not

according to the manufacturer's

instructions

so same again put that to one side now

this one i'm going to stick down

straight away

so spread it a bit here we go

i should really have gloves on right

let's put this top one on

i mean that definitely forms a stronger

bond instantly

next up is the old super glue

so i find a small piece for this because

i'm fairly certain we're not going to

use this

fairly well spread oh

this is bloody typical super glue super

blue okay next we'll do this one this is

something that was recommended by

somebody online elmer's school

pva glue

[Music]

and then we're going to do

strong pva medium

and stick that on there

let's go with the um the no-nonsense

spray contact adhesive

do this one next wow

okay and then we're going to stick it

down oh

it's bubbling there's a reaction going

on

okay next up another contact adhesive

this one

bostic leave until the glue is just

tacky approximately four minutes at room

temperature

okay that over there and then we'll just

give this a little spread as well

is this tacky yet yeah i think so

all right there we go right next up this

is e6000

plus a few blobs along there

i'm not going to spread this one because

it says to

make the surfaces okay and then we're

gonna

peel the surfaces apart and it says wait

five minutes

next up

after 10 minutes press together briefly

and firmly

right i am now going to apply the e6000

now the next thing i'm going to try

double-sided tape

first

apply now i'm going to cut around it to

a certain extent

and i am now going to peel away the

other side of the double-sided tape

ah here we go put a corner

okay and then

double-sided tape

no oh i'm still putting down let's put

the yoohoo down

right then here is the uh

finished product so we've got from the

top

gorilla glue used according to

manufacturing instructions

gorilla glue not according to

manufacturer's instructions

super glue elmer's pva strong pva

spray glue ostic contact

e6000 yuhu contact

double-sided tape double-sided tape so

yeah it'd be really interesting to see

how those come out

um i'm going to put them in a safe place

away from the kids

so they don't get tinkered with and um

come back

in uh

tomorrow wednesday thursday for a bit

more than 24 hours and then we'll we'll

have a tug at them with a pair of pliers

and um see which one is the most

appropriate

not the strongest which one's the most

appropriate so i'm gonna put that down

right then here we are for the results

it has been

um probably more like a week actually i

was gonna give it 24 hours but it's been

probably about a week so plenty of time

for this stuff to cure

properly i am now going to go through

these one by one

see how the stick is first of all see

how good that feels

then i'm going to try and pull it with

my fingers um see if i can get it off

and then if it's a struggle i'll use a

pair of pliers obviously what we're

looking for is

um it needs to be a good stick

but kind of removable fairly easily and

without

destroying the um leather wrap

so the fir the first one at the top is

the

gorilla glue clear contact adhesive

the very top one is um i

attached according to the instructions

it's a good solid bond

it's not moving so let's try and take it

off

so here we go oh jesus

that's not bad actually let's now try

same glue guerrilla clear contact

adhesive

this one applied not according to the

instructions so this is just

jammed on oh god

if anything is a bloody stronger bond

than with the uh that's pretty good

actually

it comes off pretty cleanly

i don't have it here but this next up is

the super glue plain old super glue

there it is ah

so that's um wow

yeah so that is um it's completely

breaking apart

if you look bits of the leatherette are

ripping off

see if i can even get it all off

[Applause]

wow i would not want this to be stuck to

my camera

so it i think the super glue has

actually

had quite a negative effect on the

leather actually

i'm gonna stop with that now um

don't use super glue whatever you do

jesus

right next up elmer's school pva

so i'm just i expect this one's going to

come off pretty easily but let's have a

look

still sticky underneath actually i mean

it's a relatively strong bond you know

it was um

fairly well held but definitely comes

off easily so i think

the corner of that starts to lift with

the elmer's glue on it

i think the rest of it's going to come

off pretty quickly so that one's

probably not for me i don't think

next up is the

strong art pva

this one i suspect this one will be

similar i think pvas are you know

generally designed to stand up to much

punishment

so here we go oh actually it's a pretty

strong bond

it's not bad at all

wow

pretty good quite impressed by that next

one is the spray adhesive which i'm not

um

it took ages to stick down it's really

wet

um let's have a look

not bad actually

i don't think i think not as good as the

pva uh the strong pva

plus it's really sticky yeah yeah not

not convinced about that one

uh next up bostick contact adhesive

there it is let's give this a go

wow that is again we did this according

to the manufacturer's instructions

and that is a really tight bond

yeah so let's get a pair of pliers on

that let's see what happens

oh jesus yeah a lot of it's um

coming off on the

yeah it's it's broken up a little bit so

that's just too strong too

strong e6000

e6000 plus crystal clear

which is another contact adhesive

similar formula to the rest of them

it's another one that's recommended this

one's not bad

so a good a good strong stick

but with a kind of moderate amount of

effort

comes off and it is clear

kind of gummy not too sticky

so that's quite a good one actually

[Music]

e6000

next up is the yuhu flexible and

transparent

all-purpose power so here we go

corner here that's tough

yeah so that's this i think is similar

to bostic probably a bit too much

okay

that's left a lot of um left a lot of

the leather wrap

on here you can see the patterning from

the back

so a little bit too much i'd say next up

are the two tapes and remember these are

these ones i

kind of hope will work because um

uh because if they do then

it's gonna be a very easy application

and it's you know uniform

i think this is that's pretty good huh

that's pretty good

and even that with a there was a split

in that and it hasn't

torn it now um it's mostly stayed on

here which is interesting

there's obviously another important

factor here is is whether or not we're

going to be able to get the adhesive

off the camera and whether it will clean

up

certainly not coming off easily so that

was that tape

my brand we've now got this one which is

the

tessa teaser table

now interestingly so that's all coming

off on the leatherettes

actually sticks down again i think

i think it might be the tape you know

[Music]

come off very clean but it's all on here

if you're gonna then get this tape off

here

how about that ready for reapplication

well i think we have a winner to be

honest

because

you can pre-apply it

so you can put sticky tape double sided

tape

all across the bit of leatherette that

you're working with

then cut it so you know that you have

completely kind of uniform

spread

you can then peel away the backing stick

it down

um and it looks like that is going to

come off pretty easily

leaving your leather air completely

untouched

um and and

the metal just needing to clean but that

really has worked really well i'm happy

that

that e6000 was very good as well

impressed with that

super glue big no no don't use superglue

whatever you do

pva i don't think is strong enough spray

was a bit rubbish

everybody has different ideas as to what

is the right stuff what is the best

stuff to use to uh to stick down your

leatherette

so no doubt i'll get panned in the

comments oh you didn't try this you

didn't try that

i can't i'm gonna buy every glue on the

market there are potentially

many different answers to the question

um

the most important thing is you're

sticking it down with something that

you're happy with

uh and it's going to do what you need it

to do

which is a quite unique job you need to

stick down be completely firm not peel

at the corners

and and yet peel off whenever you ask it

to

so um there we go

i hope you found this useful bye now

you