Lianli 216 ARGB Case Review Update Pros & Cons

Summary

ビデオスクリプトの要約：マイクロソフトのマイクが、Liang Li 216 ホワイトARGBケースのレビューを行いました。ケースは、Intel I9 13900kとRadeon RX 6900 XTを搭載し、垂直マウントされたグラフィックカードが目を引く見た目をしています。ファンのノイズは気になるかもしれませんが、冷却性能は優れています。ケースのフィルタリング機能は高く、前面のメッシュは埃を効果的に捕らえます。ただし、内部の配線や垂直GPUマウントの説明が不十分で、組み立てに挑戦的な部分があります。ケースのデザインは高く評価されており、価格も良心的です。マイクは、ビデオ編集用のメインPCとしてこのケースを使用する予定です。

Takeaways

• 📦 Langley 216 ケースは、白色のARGBバージョンで、一周使用した後のレビューが行われています。
• 💻 ケースには、Intel I9 13900kとRadeon RX 6900 XTという高性能なコンポーネントが搭載されており、積極的な冷却が求められます。
• 🌟 RGBファンは見た目は素晴らしいが、ファンのノイズが気になる場合はファンの速度を下げることが可能です。
• 🧹 フィルタレーション性能は優れており、前面のメッシュは非常に細かいため、積極的にダストを除外できます。
• 🔩 ケース内のファンを取り外すのは簡単ですが、垂直マウントのGPUのスクリューを締めるのは困難です。
• 🔌 トップマウントされたI/Oは、所有者の好みによっては位置が不都合かもしれません。
• 🎧 コンボヘッドセットジャックは好ましくなく、ヘッドホンとマイクを別々に挿入できるようにした方が好ましいと述べています。
• 🖥 ケースの内部レイアウトにはいくつかの問題点があり、EPSコネクタへのアクセスが難しくなることがあります。
• 💡 ケースの価格は英国で約115ポンドで、その価格帯では他に類を見ない柔软性とオプションの豊さがあります。
• 🔧 ケースの後部にあるEPSコネクタの近くのスペースが狭く、ケーブルの接続がしにくくなることがあります。
• 🛠 ケースの外観デザインは素晴らしいと評価されており、日常的なビデオ編集PCとして使用される可能性があります。

Q & A

Liang Li 216 ケースのバージョンについて教えてください。

Liang Li 216は、ホワイトARGBバージョンが存在します。

ビデオ作者が使用しているプロセッサとグラフィックカードは何ですか？

ビデオ作者は、Intel I9 13900kプロセッサとRadeon RX 6900 XTグラフィックカードを使用しています。

ケースのファン構成について説明してください。

ケースには、リーアングリが独自に作った160mmファンが3つ搭載されており、それらはRGBでアドレス可能で、渦巻きを減らすための優れた設計がされています。

ファンの騒音について述べてください。

ファンは、高速回転時にモーターの騒音が聞こえる傾向があります。また、大量の空気を移動するため、空気流の音も騒音の一部となります。

ケースのフィルタレーションについて説明してください。

ケースの前面には細かいメッシュが付いており、フィルタの効果が高く、塵やほこりを効果的に捕捉できます。

ケースのI/Oについて教えてください。

ケースのI/Oはトップマウントされていますが、ビデオ作者はサイドパネルへの移動や、追加のサイドパネルでのRGBコントロールとUSBポートの増加を好むと述べています。

ケースの垂直マウントGPUについて説明してください。

垂直マウントされたGPUは、ケースの外観を引き立てるものですが、垂直マウント用のブレースの取り付けや、GPUケーブルの購入が必要になる点に注意が必要です。

ケースの冷却について述べてください。

ケースは240mmレディエーターに対応しており、冷風を前面から導入してレディエーターから排出することで効率的な冷却を行っています。

ケースの内部レイアウトについて教えてください。

内部レイアウトは広く好评ですが、EPSコネクタへのアクセスや、CPUファンヘッダーへのアクセスが少し窮屈であることが指摘されています。

ケースの価格帯について教えてください。

英国のオペクラーズでは、現在約115ポンドで販売されており、その価格で提供される機能と柔軟性から、他の市場の製品と比較して優位性があると述べています。

ケースのRGBファンについて教えてください。

前面のRGBファンはアドレス可能ですが、背面の140mmファンはアドレス可能RGBではないことが少し残念だと感じています。

ケースの購入を検討している場合の注意点は何ですか？

ファンの騒音、垂直GPUマウントの難しさ、内部レイアウトの窮屈さ、そしてアドレス可能RGBファンの欠如などが挙げられます。これらの点を考慮して購入を決めると良いでしょう。

Outlines

00:00

📦 Liang Li 216 ケースのレビューと機能紹介

ビデオでは、Liang Li 216 ホワイトARGBバージョンのケースについて紹介しています。ケースは、Intel I9 13900kとRadeon RX 6900 XTを搭載し、垂直マウントされたトリプルファンバージョンが特に目を引いています。RGB機能は美しく、ファンは160mmのカスタムファンで、空気の乱流を減らすデザインがされていますが、ファンのモーターは少し鋭い音を立てることがあります。また、ケースの前面にはフィルターが付いており、屋内のほこりやダストを効果的に捕捉できます。

05:01

🔩 ケースの組み立てと垂直GPUマウントの課題

組み立てに関しては、垂直GPUマウントの際に、固定用のネジを入れるのが非常に困難であり、背面のファンがアドレス可能なRGBをサポートしていないという問題もあります。ケースの前面のフィルターは非常に良好で、積極的にほこりを除外できますが、組み立ての指示が不明瞭で、垂直マウント用ケーブルも別で購入する必要があります。

10:03

💻 ケース内蔵の冷却システムと风扇の性能

ケースは240mm Radiatorに対応しており、冷却パフォーマンスは良好です。ただし、バックプレートの固定には非常に力を入れないと安定しないため、注意が必要です。また、ケースの塗装には少し不満があり、他のユーザーにも同じ問題があるかどうか調査が必要です。ケースの後部には、HDDオーディオケーブルなどの接続が非常にタイトなスペースで行われているため、注意が必要です。

15:04

🛠 ケースのケーブル管理とRGB接続の課題

EPSコネクタの近くに設置されたアドレス可能なRGBコネクタは、ケーブルの接続が困難であり、ピンを曲げる可能性があります。これは、コネクタが低く設定されていなかったり、前面のセクションに移動していたりする方が良かったでしょう。しかし、ケースの後部には十分なスペースがあり、ドライブの取り付けやRGBコントローラーの追加が可能で、全体的にケースは非常に良好に機能しています。

Keywords

💡Liang Li 216

Liang Li 216は、ビデオの中心となるPCケースです。ホワイトARGBバージョンが紹介されており、レビューではその外観、機能性、そして冷却性能などが詳述されています。特に、垂直マウントされたグラフィックカードがケースの見た目に寄与しているとされています。

💡RGB

RGBとは、赤(red)、緑(green)、青(blue)を意味し、ビデオではケース内のライトの色をカスタマイズする機能として説明されています。RGB機能は、ビルドの見た目をスペクタクルに見せるために重要な要素です。

💡ファン

ファンは、cased内の冷却を担当する部品で、そのノイズや空気の流れがビデオで問題視されています。特に、ファンのモーターが騒音を発生させる傾向にあると述べられており、冷却と騒音のバランスが重要なポイントです。

💡垂直マウント

垂直マウントは、グラフィックカードをケースの前面に立てる方法で、ビデオではその見た目が高く評価されています。垂直マウントによってカードの重さによる下垂を防ぎ、サポートが強化されるとされています。

💡冷却性能

冷却性能は、ビデオで強調されている重要なポイントで、インテルI9 13900kやRadeon RX 6900 XTなどの高性能なコンポーネントから発生する熱を処理する能力に関连しています。冷却の良い状態を維持するためには、ファンの速度調整や冷却システムの最適化が必要です。

💡ダストフィルター

ダストフィルターは、cased内の埃を防ぐための機能で、ビデオでは前方のメッシュがその役割を果たしていると説明されています。ケースのフィルターは、埃を効率的に捕捉し、内部の清潔さを保つために役立ちます。

💡ファンの交換

ファンの交換は、冷却性能や騒音レベルを改善するためにビデオで提案されています。120mmファンに交換することで、より良い冷却効率と静かな動作を実現できるとされています。

💡I/Oポート

I/Oポートは、ケースの前面または側面にあるポートで、キーボードやマウス、USBデバイスなどの接続に使用されます。ビデオでは、トップマウントされたI/Oポートの位置が問題視されており、ユーザーがそれに基づいて位置を調整できるオプションが提供されていると述べられています。

💡組み立て

組み立ては、ビデオの主なテーマの一つで、Liang Li 216ケースを使ったPCの組み立て方法が説明されています。組み立てには、グラフィックカードの垂直マウント、冷却システムの設定、ファンの交換など、様々な手順があります。

💡ケースの設計

ケースの設計は、ビデオで高く評価されている要素で、特に見た目の外観と機能性のバランスが高く評価されています。ただし、組み立て時のアクセシビリティや内部レイアウトの課題も触れられており、ユーザーには注意喚起されています。

💡価格

価格は、ビデオでケースの価値を判断する際の重要な要素です。Liang Li 216の価格は、英国で約115ポンドとされており、その価格で提供される機能とデザインのバランスがビデオ内で評価されています。

Highlights

Liang Li 216 case review by Mike from Microsoft reviews

The case features a white ARGB version with a custom design that stands out when components are housed inside

Intel I9 13900k and Radeon RX 6900 XT used in the build, generating significant heat

Vertical mounting of the Radeon RX 6900 XT triple fan version enhances the visual appeal

The case offers extensive RGB lighting customization

Custom made 160mm fans with RGB addressing and a shroud for reduced turbulence

Fans can become noisy under heavy load due to motor noise and airflow

The front mesh filter is effective at preventing dust intake, maintaining cleanliness

Easy removal of the front panel for maintenance, requiring only six screws

Top-mounted I/O with an option to move it to the side panel for better accessibility

A combo audio jack is less desirable, with a preference for separate microphone and headphone jacks

The clear glass side panel showcases internal components effectively

Instructions for vertical GPU mounting are unhelpful, requiring additional research or purchases

Installing the GPU vertically can be difficult due to the depth-set screws

Internal layout allows for a 240mm radiator and includes a blanking plate for improved airflow

The case is priced at just over 100 pounds in the UK, offering good value for its features

A slight defect in the paintwork was noted, which may affect the overall aesthetics

The case is highly recommended for its design, flexibility, and cooling options, despite minor drawbacks

Transcripts

but it's Mike from Microsoft reviews now

too and on today's video we're going to

do a quick wrap up on the Langley 216.

there are some pros there are some cons

keep watching to find out more

[Music]

okay so today's video we'll be taking a

look at the Liang Li 216 in White argb

Version as you can see here and I've

been using this as my daily driver for

about a week or so now and I thought I'd

give you guys a little bit of a wrap up

and uh kind of informative overview of

the case now we went through and did the

unboxing which you're more than welcome

to check out first of all that'll be

linked somewhere in the video

description or up here at wherever it is

these days

and you can check out my initial

Impressions but now after doing a full

build in here I can give you a little

bit more in depth the build that you've

got in here is a Intel I9 13900k so

plenty of heat coming from that one

we've also got a Radeon RX 6900 XT so

again plenty of heat from that and as

you can see from some of the b-roll and

probably from here you can see we've got

it vertically mounted which I figured

actually makes this actually pop a

little bit more I think it looks very

nice the triple fan version looks

absolutely amazing

okay let me know what you think in the

comments section if you're not

particularly into RGB in this case might

not be the one for you but certainly if

you are I think it offers a lot of

things you can do in terms of lighting

and actually making the build look

pretty spectacular one of the first

things you're probably going to notice

and if I'm completely silent you can

possibly hear it and that is the noise

of the fans

there is a few pros and cons with the

fan set up as standard so Leanna Lee

have put in their custom made 160 mil

fans which are addressed by RGB and

actually they've done a fantastic job of

them the shride that goes around them is

excellent for reducing things like

turbulence so if you look from the

inside you can see there's like a

plastic wedge in between the fans so you

don't get any of that kind of weird

turbulence of airbn sucked in or

basically recirculine air so that works

really well the fans themselves the

motors do seem to have a little bit of a

kind of not so much a tick but more of

like an aggressive sound so when the

fans are ramped up you do hear some

motor noise and also due to the fact

that it's just moving an absolute ton of

air you do hear airflow so if you do

want a completely silent PC and you are

going to be using relatively uh hard to

cool components then you may want to

think about the cooling situation now

obviously you can go into your

motherboard's control setup and actually

reduce the speed of the fans obviously

that is going to reduce the cooling

potential and all that kind of stuff but

something which I think a lot of people

if you're potentially looking at this

and you're seeing pictures online you're

looking and thinking wow that looks

amazing but unfortunately the the same

profile isn't particularly good and I

would certainly suggest if you are

thinking of going this route and you're

going to have some components which are

pretty hard to cool you might want to

swap out the fans for 120s in general

120 mil fans do tend to have a better

signature overall okay let me know what

you think about that in the comments

section something which this case does

really well is filtration the front mesh

is the only filtration actually on the

front there isn't a mesh filter behind

it or anything so it does a good job

it's quite a fine mesh and it's spaced

out really nicely from the fans

themselves and I have found on a morning

because we have cats Etc and uh there's

the usual debris that you get inside of

most houses especially when you've got

things like a wood burner all that kind

of stuff then you do get a lot of dust

but I've found pretty much every morning

just go like that that in the front and

it basically removes all the dust and

inside is basically perfect doesn't seem

to be a great deal of thus getting

actually inside so most of it is being

stopped by this front panel

with the front panel off you can see

inside a little bit better so again this

is the Sarang I was referring to the

fans so most fans traditionally kind of

stop at the outer ring whereas they've

added on a little bit of height top and

bottom to kind of prevent some of the

contributes that kind of stuff and I

think they look really good there has

been some discussion at least I've seen

from a separate control panel you can

get that you can control the inner ring

and the outer ring separately I'm not

entirely sure how that works it doesn't

appear to be something which you can do

basically there's a kind of random thing

depending on what the rest is doing but

overall I think the fans themselves in

terms of looks look absolutely amazing

and from some certain angles with the

mesh on the front it gives a really nice

overglow removing the fans on the whole

front assembly is very easily as we saw

from the teardown so just six screws to

the top two at the bottom two in the

middle and you can pull this panel out

to make any adjustments that you need to

something which I wasn't overly Keen of

in terms of the i o so the top mounted i

o isn't a good position for me because

generally the PC is a little bit lower

down you can if you want to move it from

here to the side panel you can also get

an additional side panel which gives you

more RGB control over the fans and also

a couple of extra USB type A ports so

that might be something you're

interested in or potentially move it if

that suits something which I don't like

is the fact that we do have a combo

headset made Jack I'm not a big fan of

those I would much prefer to have seen a

separate headset microphone Jack so you

can split the two should you need to

quite often I find myself plugging in

headphones without a microphone and yeah

this is one of these things it's a

little bit annoying so that was

something I would have liked to have

seen different now looking from the side

you can see I think the build is

actually turned out very nice indeed the

graphics card really does fill out what

is going on inside there even a smaller

card actually doesn't look too bad in

there I think this is pretty much

perfect there aren't many cards which

are much longer than this particular MSI

one so I think it's done a pretty good

job and the glass itself being

completely clear as you can see I think

uh lets you see inside the components

very nicely there's a few things which

I'd have liked to have changed

internally mostly down to wiring but one

of the key things if you are going with

a vertical mind is the fact that in the

instructions it's very

um

oh it's unhelpful it doesn't tell you

what you actually need to use or where

you need to put the vertical mounting

bracket on the bottom there are two

pillars which stand up it turns out the

ones that are in the box is the longest

of the two there are multiple options in

there especially because you've got

extra motherboard pillars which

basically are exactly the same so if you

are building in this and you're planning

on doing vertical GPU installation this

doesn't actually come with a vertical

GPU cable so you will need to buy one of

those separately I picked one up very

cheaply off Amazon from easy DIY and it

cost me about 30 pounds which is a lot

of money for what it is but it seems to

do a very good job and performance has

been absolutely great I find actually

with this particular card because of it

is quite a chunky Beast having it

vertically mounted actually obviously

eliminates sag altogether because you

don't have that kind of overhang and it

is very well supported even though the

base is perforated as we said earlier on

in the video

taking the slow panel off and the front

panel is very easy so it just pops off

after you undo the screw and with it

removed you can see inside a little bit

better something which is an absolute

pain in the ass and has been done badly

in my opinion is if you are vertically

mounting your GPU actually getting

screws into the graphic score to hold it

in place is nion impossible they are

very deep set and because of the fact

that it is right up against the back you

can't get a screwdriver in there unless

you remove your fan and even then you're

still going to need a relatively small

screwdriver to get in there so in my

opinion that is something which has been

done particularly badly and as it stands

at the moment I've only got one screw

holding in the graphics card and because

I can't really access it particularly

well the screw isn't even fully

tightened so there is a very small

amount of Wiggle on there which I'm not

overly happy with but having said that

I've moved it around from its usual

location to here and vice versa and it

hasn't caused any problems but here's

something which I feel they could have

done much better in terms of the layout

internally as well I think they've done

a pretty decent job this is currently

set up in what they call the kind of

water cooling mode so the motherboard is

in a lower position

allegedly giving you more room up the

top but with the radiator installed up

here it's almost impossible to get to

the EPS connector so potentially you

will need to undo the screws on the side

and pull this panel out when you're

doing any of those connections which is

a little bit of a pain but it is

workable it's not the end of the world

but I would like to have seen a little

bit more height possibly in the case

just to gain a little bit more access

there make things a little bit easier

the same applies for things like the CPU

fan header Etc because they're all

generally mounted at the top it's quite

a squeeze to get into them something

else which is not really relevant to the

case itself but something which I am

going to change is the actual

connections so we've got eight pin

connections going into the graphics card

there's three of them and because they

are going outward it's a little bit

untidy in this area here so you can

actually buy 180 degree adapters so you

plug them in on the 8 Pin and then you

plug your cables in they kind of slot in

in behind which will reduce some of the

airflow to the backside of the card

which isn't entirely necessary but just

something to be wary of those you can

pick up for about 10 pounds for a set of

three so that's a pretty good to do also

ugly Bob did send us over a couple

already but there was only one eight pin

one so we're gonna have to buy a few

more of those but that's quite an easy

thing to do something else I'm not

overly keen on but it isn't the end of

the world is the fact that at the back

there we've only got the single 140 mil

fan which isn't addressable RGB which in

terms of the price for this currently

it's somewhere just over 100 pounds here

in the UK I don't think it's a totally

unforgivable it would have been nice to

have had possibly the option of maybe

paying another 10 pounds and having an

adjustable RGB one which matches the

front two because they are quite unique

looking so actually getting another fan

to kind of matching or blend in might be

a little bit uh tricky again if you're

planning to replace the fans entirely

then it isn't a problem

when it comes to cooling if you're

putting a 240 mil Radiator in there

there is a blanking plate which goes at

the front which if I tilt this backslide

you should be able to see and I've also

filmed on b-roll so you can see it so

that actually does help quite a bit

because it stops air escaping so you've

got your cold air coming in from the

front which is being pushed through and

then basically the first point of exit

is going to be through the radiator so

this keeping things nice and cool again

this is a Intel I9 3900k with only a 240

mil AIO which generally isn't quite

enough but with a little bit of

undervolting and setting your TDP limits

Etc and decent airflow from the k-switch

this certainly does have it's managing

to keep it under control quite nicely

the blanking plate itself I think is an

excellent inclusion and obviously if you

are going for a 240 Leo or just mounting

two fans in the top then it's definitely

worth installing it although you will

find when you install it the screws

which actually hold it in place do need

to be quite aggressive so if you think

they're tightened they're not just keep

on tightening until you hit a hard wall

otherwise you will find that it's a

little bit loose and potentially

I did do it I was just checking to make

sure I actually did re-tighten the

screws because they do require an

extreme amount of force to make it tight

and to stop it vibrating something else

which was a slight niggle for me

um which possibly isn't going to affect

everybody for those of you that saw me

do the unboxing in the live stream and

potentially from the video you'll notice

there was a very slight defect in the

painting in this area it's not

particularly evident on camera here you

can just about make it out there where

some of the paint appears to have either

rubbed off or has not been quite done

thick enough so it is a slightly

different color there again if it was

you buying it from a shop brand new such

as overclockers Etc then it's a strong

chance that isn't going to be a problem

for you but if you have got this case do

check out your soy panel and let me know

is yours got the same thing is it

something which has happened in

manufacture which affects all of them or

is it just down to this particular model

do let me know something else as well

actually having this section here being

removable is actually pretty handy for

more reasons than not because actually

getting to some of the cables can be a

little bit tricky because the actual

depth here isn't huge when you've got

your power supply in there it is

actually quite tight so sometimes you

might not be able to access things quite

as easy and being able to take this

section out and get in there and kind of

tweak and mess around with things is

quite a valuable thing in my opinion

from the back not a great deal to report

on everything is pretty much fine the

two screws at the top for removing the

top panel very handy indeed especially

if you need to do any maintenance to

your radiators Etc and also again for

getting to the EPS connector which can

be slightly trouble some the rear

section here where they have the

vertical mounting so at the moment this

is in the vertical mounting option you

will find depending on where you mount

your graphics card I've tried to mount

it kind of so it's almost in the middle

it's uh it's the furthest forward it can

go

do better than mine because your

connections on the back for HDMI and

your display ports Etc potentially might

be slightly blocked there because it

does kind of tuck in behind this last

section here so you there are three

positions you can do it so you can move

it back a little bit more but then it

does get quite close to the motherboard

so if you do have to do anything with

connections such as your front USBS HD

audio that kind of stuff it's almost

impossible to get to but I find with it

being pulled out as far as it can at

least you've got a bit of a fighting

chance of getting to them again from the

back not really much else to report on

apart from the distinct lack of

addressable RGB from this fan on the

back

moving around to the back of the case so

here is absolutely fine there's one or

two things which potentially could be

issues for you depending on your power

supply and things like that I do find

that the gap between the bottom here

especially with the HD audio cable

connected is very tight so you will find

yourself potentially moving the drive

base slotting the power supply in from

the front here and then bringing it back

in would have been nice to have a

separate Drive bracket on the back so

you can just slot it in from the back

that was a pain that really was that is

way too close obviously if you're not

connecting up your HD audio or any other

Connections in this area then you'll be

fine but certainly put your power supply

in first there's my uh my recommendation

then put the cables through after I made

that mistake hopefully you win something

else which is worth bearing in mind is

on the back here so you've got this

panel which covers up the back of the

CPU area

with our particular cooler there is an

additional backplate and it is extremely

close to this section here so

potentially depending on your

motherboard and the kind of tolerances

you may actually find you having to

remove your motherboard from the case to

change coolers or do modifications Etc

this one does come extremely close as

you've probably seen for some close-ups

I did a little bit earlier

talking of close as well on the back if

you're putting in your EPS connector

which runs up nicely through these

little plastic grippers or cable

management channels which actually do

work very well I haven't used I don't

think I used any cable ties at all

actually on here it's all tucked in so

that is definitely good and obviously

the velcro straps certainly help with

that this isn't the neatest it could

possibly be but it's uh it's pretty okay

this I think could have been moved

somewhere else I.E lower would been

great

um it's a bit of a pain because it's

actually mounted onto kind of

motherboard pillars so moving it isn't

particularly easy but you do find it

actually trying to plug things into this

because of how high it is you actually

Bend some of the pins especially

addressable RGB ones because those are

always a pain in the backside so I have

actually bent some of the pins on there

already trying to get the cables in

because the clearance at the top just

isn't quite enough if this would have

been a little bit lower would have been

no problem at all or potentially with it

being kind of in this section at the

front where there's not really a great

deal going on I think that would have

been a simpler and easier solution to

use going forward

especially if those were kind of facing

that way would have given you a lot of

room to get into and also putting the

EPS cable through there especially when

you've got all your RGB cables in the

way can be a little bit problematic but

it isn't something that you can't

overcome just obviously do bear in mind

and ideally like I said try and do your

power supply mountings and cables first

well if you possibly can other than that

in the back I think they've done a

pretty good job it's nicely spaced out

you've got a decent amount of depth

there so if you're mounting drives or

maybe an RGB controller on here which I

potentially might do I might remove this

one and actually put in a dedicated

controller at some point and if I do a

mount on there just to give me a bit

more room at the top for swapping out

EPS cables and other cables as I'm

testing other components in this rig so

there you go overall very nice case to

work in a few little quirks which you

might want to pay attention to and there

might be some deal breakers I don't know

fan wise you probably will want to keep

these under kind of 60 of their full

speed otherwise they are going to get

quite noisy there is yeah there is just

a sound of airflow which is one of those

things it's an airflow orientated case

you've got 160 mil fans so they are

moving a lot of air and there's not

really a great deal you can do to make

those quieter apart from like I said if

you want to swapping out the fans which

then potentially kind of spoils the

whole look of it which I think in terms

of case design I think they've actually

nailed it and for the current asking

price about 115 pounds at the moment

from overclockers.com here in the UK

I don't think there's much else on the

market which competes with it in terms

of overall what you can do the

flexibility the options of having 360

rad in the top or the front

other things which you can change out

the vertical mounting Etc yeah I think

they've done a fantastic job and I'll be

honest I was a little bit hesitant but I

am actually genuinely quite pleased with

this and I'm pretty sure it's going to

stay as my daily driver for my video

editing PC for the foreseeable that is

until something comes along which is

better which is pretty much always the

case speaking of cases this has been the

Liang Li 216 in white argb hopefully

you've enjoyed this video and it's given

you some food for thought if you're

planning on a build or maybe upgrading

if you are then links will be in the

video description so you can pick them

up for yourself also you do it in the

RGB non-rgb and also black and white so

there should be pretty much something

for everyone and certainly I would

recommend it just be aware of some of

the caveats so there you go that's been

the only 216 argb in white I've been

Mike this is Michael unboxing reviews on

how to and hopefully we'll catch you in

the very next video

thanks for watching

[Music]