How to set up the F & P BCPAP Device
Summary
TLDRIn this tutorial, Richard demonstrates how to set up a fish tank bubbler system. He explains the installation of the bubbler, heater, and O2 tubing, including integrating an O2 analyzer and a safety pop-off valve. He also covers the proper setup of the heated and non-heated circuits, leak testing, and adjusting the flow rate using a Hudson prong. The video concludes with tips on maintaining the system and managing water overflow.
Takeaways
- 🐟 Setting up a fish tank involves a bubbler and a heater with a bracket.
- 🔌 A pop pressure pop off valve is used, similar to a high flow valve.
- 🔬 An O2 analyzer can be integrated by removing a blue cap and sliding it in.
- 🔧 A safety feature is the 40 PSI pop off for back pressure.
- 🌡️ The circuit has a heated blue limb and a short non-heated section, leading to expected condensation.
- 💧 A temperature probe is crucial and should be pushed all the way in to avoid additional condensation.
- 🌡️ A V-knot in the circuit is important for flow and temperature probe alignment.
- 💧 Water is added using a removable funnel, filling the tank until water overflows to the second chamber.
- 💨 Leak testing involves setting the flow meter at 1 liter and observing bubbles in the bubbler.
- 🔌 The Hudson prong fits directly into the Houston PR without needing a special adapter.
- 🌊 Regularly pouring a little water while bubbling ensures proper overflow observation and maintenance.
Q & A
What is the purpose of the video?
-The purpose of the video is to demonstrate how to set up a fish tank bubbler seat, including the installation of various components and the testing of the system.
What is the first step in setting up the bubbler seat?
-The first step is to place the bubbler with the bracket already in place or slide it in behind the heater.
What is the function of the pop pressure pop off valve?
-The pop pressure pop off valve is used to release pressure and prevent back pressure in the system.
How does the O2 tubing connect to the pop off valve?
-The O2 tubing is connected to the pop off valve by removing the little blue cap and sliding the tubing in.
What is the advantage of integrating the O2 analyzer?
-Integrating the O2 analyzer allows for direct analysis of oxygen levels without needing a T adapter.
What is the purpose of the circuit with a blue limb and a short 8-inch non-heated limb?
-The blue limb is a heated wire, and the short non-heated limb is designed to expect some condensation build-up, which is normal.
Why is it important to push the temperature probe all the way in?
-Pushing the temperature probe all the way in ensures accurate readings and helps avoid additional condensation.
How should the dual limb heated wire be installed?
-The short limb should be placed in the back of the circuit, and the other limb can be left hanging.
What is the purpose of the V knot in the circuit?
-The V knot is important for the flow and temperature probe, and it should be worked in as hard as possible until it flushes with the V.
How do you test the system for leaks?
-To test for leaks, set the flow meter at one liter, use the elbow adapter, and check if bubbles appear when the cap is removed and reappear when the cap is put back on.
What is the Hudson prong used for?
-The Hudson prong is used to fit directly into the Houston PR without needing a special adapter, and it helps in adjusting the flow rate.
How should you monitor the water level in the system?
-You should pour a little bit of water while it's still bubbling to ensure the overflow is visible, and make sure the water does not exceed the maximum line to prevent it from inadvertently going back into the chamber.
How do you dispose of excess water from the system?
-To dispose of excess water, lift the canister up, slide it out, pour the water into the sink, and then put it back into the groove and drop it.
Outlines
Этот раздел доступен только подписчикам платных тарифов. Пожалуйста, перейдите на платный тариф для доступа.
Перейти на платный тарифMindmap
Этот раздел доступен только подписчикам платных тарифов. Пожалуйста, перейдите на платный тариф для доступа.
Перейти на платный тарифKeywords
Этот раздел доступен только подписчикам платных тарифов. Пожалуйста, перейдите на платный тариф для доступа.
Перейти на платный тарифHighlights
Этот раздел доступен только подписчикам платных тарифов. Пожалуйста, перейдите на платный тариф для доступа.
Перейти на платный тарифTranscripts
Этот раздел доступен только подписчикам платных тарифов. Пожалуйста, перейдите на платный тариф для доступа.
Перейти на платный тарифПосмотреть больше похожих видео
Tiny Homes On Wheels DIY : Chapter 7 - Plumbing - Tumbleweed Tiny House Company
How to Light or Relight Your Water Heater Pilot
Pressure Testing Cooling Systems -EricTheCarGuy
Membuat Aquaponik Drum Pelihara Ikan Lele & Menanam Kangkung Di Kebun Halaman Rumah | FULL VIDEO
Micro Hydro Startup 2023
Reynolds Experiment | Fluid Mechanics
5.0 / 5 (0 votes)