The ONE GAME-CHANGING Slicer SETTING... (Huge 3D Print Quality BOOST)
Summary
TLDR3Dプリンタで層の不一致を解消する方法について解説した動画の要約です。まず、スライサーの設定を調整することが肝要で、特に外周壁を先に印刷する設定が質の向上に大きく寄与すると述べています。また、エクストルーダーの設計や印刷速度、フローレートの影響も触れています。テストプリントを通じて、デュアルギアとシングルギアのエクストルーダーを比較し、外周壁を先に印刷することで層の一致性とオーバーハングの質が向上することが示されました。ABSやASAフィラメントでのテストも行われ、同様の結果が得られています。最後に、Orca Slicerでの比較プリントの方法や、見解を共有するよう呼びかけています。
Takeaways
- 🔧 3Dプリンタで層の均一性が良くない場合は、スライサーの設定を調整することが肝心です。
- 🎯 PLAとABSフィラメントで複数のプリンタでテストされ、効果が確認されたスライサー設定があります。
- 🛠️ ノズルのダブルギアとシングルギアの違いがあり、シングルギアの方が貫通性の良いエクストリュジョンが可能です。
- 🚀 遅い印刷速度でフィラメントがホットエンド内で長時間加热されると、層の幅が変動する可能性があります。
- 🔥 高フローホットエンドで同じ速度で印刷し、可能な限り高速で移動することが、層の一貫性を高める方法です。
- 🧱 外周壁を先に印刷することが、驚くべきほどの質の向上をもたらすと述べています。
- 🤔 Orca Slicer 2.0を使用して、内側/外側/内側の壁の順番で印刷することで、ブリッジを印刷する際の熱塑性材の貫通性を改善します。
- 📈 テスト結果によると、外周壁を先に印刷することで、層の一貫性だけでなく、オーバーハングの質も向上することが示唆されています。
- 📊 消費者向けの3Dプリンタの多くは冷却が不十分で、テストプリントで苦労する傾向がありますが、改善された冷却システムは効果的です。
- 🔄 ABSフィラメントでのテストでも、外周壁を先に印刷する設定は驚くべき結果を出しており、より良いオーバーハングを実現しました。
- 📝 Orca Slicerで簡単に比較プリントを行うことができ、全体タブからオブジェクトを選択し、壁の順序を変更するだけで試すことができます。
- 🌟 この設定が印刷品質に多大な影響を与えることを示唆し、広く知られるべき価値があると結論づけています。
Q & A
3Dプリンタで層の不一致が気になる場合、どのようなスライサー設定が効果的ですか?
-外側の壁を最初に印刷する設定が、3Dプリンタの層の不一致を改善する効果があります。これは、オーバーハング部分の懸念を除くためにも役立ちます。
スライサー設定を変更する前に、どのような点を理解しておく必要がありますか?
-スライサー設定を変更する前に、エクストルーダーの精度や、異なるフローレートと速度での印刷が層の不一致に与える影響を理解しておく必要があります。
デュアルドライブギアとシングルドライブギアのエクストルーダーのどちらが優れていますか?
-シングルドライブギアのエクストルーダーは、より一貫性のあるエクストリュジョンを提供する傾向がありますが、問題がないデュアルドライブギアのエクストルーダーも十分に良い結果を生むことができます。
ホットエンドのフローレートが低い場合、どのような影響が予想されますか?
-ホットエンドのフローレートが低いと、フィラメントがホットエンド内で長時間加热され、熱伝達性が低いプラスチックの壁の幅が大きくなってしまいます。
テストプリントで作成された2つのスロットは何のためにありますか?
-テストプリントの2つのスロットは、インフィルを印刷しないことで、ブリッジをゆっくりと印刷する際にフィラメントがホットエンド内で長時間加热される様子を示すためにあります。
Orca Slicer 2.0で使用される内側/外側/内側の壁の順序は何ですか?
-内側/外側/内側の壁の順序は、ブリッジをゆっくりと印刷する際に、まず内側の壁を印刷し、その後外側の壁を印刷することで、より一貫した品質のプリントを実現します。
トラベルディスタンスしきい値とは何ですか?
-トラベルディスタンスしきい値は、わずかな距離を移動して外側の壁を印刷する必要がある場合に、不必要なリトラクションやZホップを排除する設定です。
テストプリントで使用されたクーラントテストプリントはどのような効果を持ちますか?
-クーラントテストプリントは、各プリントが予想以上の結果を出したことを示しており、特にPLAの場合には、外側の壁を最初に印刷することでオーバーハングも向上することがわかりました。
ABSフィラメントでこの設定を使用する効果はどのようでしたか?
-ABSフィラメントで外側の壁を最初に印刷する設定を使用すると、層の一致性とオーバーハングの両方において、内側の壁を最初に印刷するよりも大幅に改善された結果を得ることができました。
Orca Slicerで壁の順序を変更するにはどうすればよいですか?
-Orca Slicerで壁の順序を変更するには、グローバルタブからオブジェクトを選択し、印刷を選択して、異なる壁の順序オプションを選ぶことができます。
3Dプリンタで得られる層の一致性は、どのような要因によって影響されますか?
-3Dプリンタで得られる層の一致性は、エクストルーダーの設計、印刷速度、ホットエンドのフローレート、および壁の印刷順序などの要因によって影響されます。
スライサー設定の変更によって、実用的な部品の精度はどのように向上しますか?
-スライサー設定の変更、特に外側の壁を最初に印刷する設定は、実用的な部品の精度を向上させるだけでなく、オーバーハングの品質も改善する可能性があります。
Outlines
😀 3Dプリンタの層の一貫性を高める秘訣
この段落では、3Dプリンタの層の一貫性を高めるためのスライサー設定について解説しています。スポンサーセグメントの後に、PLAとABSフィラメントで複数のプリンタでテストされたと述べています。また、CNC加工や3Dプリンティング、PCB製造など、プロジェクトに必要なプロフェッショナルサービスを提供するPCBWayについても紹介しています。さらに、エクストルーダーの精度の問題や、印刷速度とフィラメントの熱状態が層の一貫性に与える影響についても触れています。最後に、外側の壁を最初に印刷することで質の高いプリントを実現できると結論づけています。
🤔 外側の壁を最初に印刷する設定の効果
この段落では、外側の壁を最初に印刷する設定がABSやASAフィラメントで使用した際の驚くべき効果について説明しています。Bambu X1CやQIDI Q1 PROなどのプリンタでのテスト結果を紹介し、層の一貫性とオーバーハングの改善が顕著であることを強調しています。また、この設定が実用的なパーツのフィットネスにも良い影響を与えると述べ、オーバホールの印刷に関しては、極端な角度を除いて悪化するリスクはないと結論づけています。最後に、Orca Slicerでの比較プリントの簡単さや、見た目と品質を向上させる設定の共有を促しています。
Mindmap
Keywords
💡3Dプリンタ
💡スライサー設定
💡PLAフィラメント
💡ABSフィラメント
💡エクストルーダー
💡層の一致性
💡ホットエンド
💡ウォールオーダー
💡オーバーハング
💡トラベルディスタンスしきい値
💡テストプリント
Highlights
A specific slicer setting can significantly improve the consistency of 3D printed layers.
The setting has been tested with PLA and ABS filaments on multiple printers.
PCBWay offers professional services like CNC machining, 3D printing, PCB manufacturing, and more, with a discount for first-time buyers.
Dual drive gears in extruders can lead to inconsistent extrusion compared to single-drive gears.
Prusa MK4 and Bambu Lab A1 series use single drive gears for more consistent extrusion.
Inconsistent layer lines can be caused by printing at different flow rates and speeds.
A high flow hotend and consistent print speeds across all features can help combat layer inconsistency.
Printing outer walls before inner walls can greatly enhance print quality, even with overhangs.
Orca Slicer 2.0's inner/outer/inner wall ordering option is recommended for better print consistency.
The Travel Distance Threshold setting can reduce unnecessary retractions and z-hops.
Calibrating the flow rate is crucial for the effectiveness of the slicer setting.
Single-drive gear extruders, like those in Bambu Lab A1, provide more consistent results than dual-drive extruders.
The outer wall first setting surprisingly improves overhangs in many cases.
The setting works well with both PLA and ABS filaments, even producing better overhangs with ABS.
The setting not only improves layer consistency but also provides better tolerances for practical parts.
Quick comparison prints can be easily done in Orca Slicer to test the effectiveness of the setting.
Sharing similar settings that improve print quality can lead to more widespread knowledge and better 3D printing practices.
Support from Patreon and YouTube helps in creating informative and helpful content for the 3D printing community.
Transcripts
So you have a mechanically sound 3D printer, but can’t get those layers to look more consistent?
Then you need to try one slicer setting that will truly do wonders. And no this is
not a bait! I have tested this with PLA and ABS filaments on multiple printers! So let's reveal
probably the least intuitive slicer setting after today's sponsored segment from PCBWay.
If you are looking for professional services like CNC machining, 3D printing even from metal,
PCB manufacturing, or the full range of all other services that are required for your projects,
make sure to check them out with the link in the video description and get
five bucks off for your first purchase. Before you apply the setting that truly
makes wonders, first you must know the other two main factors that can significantly add
up to this inconsistency. You might think that our extruders have surgical precision,
but in reality, they just DO NOT. Even the most common extruder design
that has dual drive gears pushing the filament has a fundamental issue of those gears never meshing
perfectly. That will lead to less consistent extrusion compared to the single-drive gears.
This is nothing new and lately, we started to see the glimpses of
these types of extruders coming back to the marker. Prusa MK4 uses a single drive gear,
Bambu Lab A1 series uses a single gear, and you can even print and make one from
a kit as a standalone extruder or drop-in replacement for your Voron.
So, the improvement you will get with that one magical slicer setting will depend on how
consistently your printer can extrude the plastic in the first place. But don’t get me wrong you
will still see a noticeable difference even with dual-gear extruders that has no glaring issues.
Another factor that will make your layer lines less consistent is printing at different flow
rates and speeds. The slower you print the more time filament spends in the hotend. As
plastics have a very low thermal conductivity your extruded wall width will depend a lot on
how long the filament spent in the hotend. To better show this effect I created a test print.
It has two slots where no infill will be printed. This means that we’ll be slowly
printing bridges. That will lead to the filament spending more time in the hotend and being heated
more. And after we are done bridge’ing, we will be printing perimeters of the next layer
with way more heated filament resulting in slightly bulged and more shiny layer lines.
This is probably the least explored aspect of why prints have inconsistent layers. The only way to
combat this, that I know, is to have high flow hotend, print slow with the same speeds across
all features, and travel as fast as possible. So with all this out of the way, the one setting
that will give an insane quality boost to your prints is printing the outer walls first,
before the inner ones are printed. You might be very skeptical about this because of the
overhangs, but this is where your mind might be blown for the second time.
In the Orca Slicer 2.0, for all my print comparisons I used the inner/outer/inner
wall ordering option. In my opinion, this is the best order, as when we slowly print bridges,
it will first print the inner walls to flush that hotter filament, then print the outer
one, and finally finish the last inner wall. The only additional setting that you might look
into is the Travel Distance Threshold. In this case, it will eliminate unnecessary retractions
and z-hops when we only need to travel just a bit longer distance to print that outer wall.
So now let’s dive into the comparisons. I started testing with a printer that has a
dual-drive gear extruder. The first thing I did on all the printers was to calibrate the flow
rate for the printing speeds I would use. In the beginning, I tested printing inner walls first
with the Precise Wall option in the Orca Slicer. What this option does is it prints the outer wall
without squishing into the inner one. This leads to a small improvement on my fully modded KP3S
PRO printer, but it comes nowhere even close to what improvement we get when printing the
outer wall first. I also tried combining the outer wall and precise wall option
but as expected there was no improvement in the layer consistency of the print.
Next, I ran the same test print on the Bambu Lab A1 which has a single filament
drive gear. Before we look into comparisons between two printers it is good to see how
extrusion consistency looks when comparing two tested extruder types. Like I said before,
a properly functioning dual-drive extruder is good enough but as you can see the single-drive gear
results are just objectively more consistent. When printing the inner walls first, the A1
prints look almost as nice as with the dual-gear extruder when printing the outer walls first.
The Precise wall option with A1 made a small improvement, but yet again the
difference that printing the outer wall first makes is just on a completely different level
and the print looks almost flawless. Well, that’s great, but I think all of
us want to know how this setting performs with overhangs. Well… With my designed cooling test
print literally every print from PLA surpassed all of my expectations. It seems that printing
outer walls first can result in worse overhangs only at extreme angles. But it will also depend
on your cooling setup, as my fully modded KP3S PRO performed just as well at those extreme angles.
You might think that this is a very forgiving test print but I rest assured that it is not and many
of the stock consumer 3D printers struggle a lot as their cooling is just not that good.
While with more organic prints the layer consistency improvement will be very minimal,
in some areas I saw better overhangs by printing the outer wall first. I know,
it just feels like it makes no sense, but all my test prints from PLA were so much better looking
and I had no problems printing overhangs. Not to mention that printing the outer walls first will
make your practical parts fit perfectly. This leads to the question of how this one
setting works when printing ABS. This is where your mind will be blown even more.
The results with Bambu X1C felt completely absurd as higher overhangs looked so much
better with printing the outer wall first. Surely it is just a fluke… Right?! So I
switched to another brand ASA filament and a more budget QIDI Q1 PRO printer. But nothing
changed. When printing the outer walls first it gave a print that is just on a different level
when it comes to the layer consistency and the overhangs continued to be better compared to when
printing the inner walls first. I printed and compared more things
like this USB cable holder or a way more complex Voron part that yet again had an
insane improvement in print quality. I also tested on more printers and this
made me realize that even I and 75% of you, are missing out on something incredible.
From my testing, this option not only makes wonders to layer consistency in your prints,
but I didn’t even find any significant downsides when printing overhangs and in some cases,
they even can become better. Plus it also gives you way better
tolerances for all of your practical prints. So give this setting a try, especially as making
quick comparison prints is very easy to do in Orca Slicer. All you have to do is go from the Global
tab into the Objects, select the print, and choose the different wall ordering option.
You can post your prints and with what 3D printer you made them on Twitter,
as it will be interesting to see what your experience is with all this.
If you have discovered any similar settings that make significant improvements to the
print quality, make sure to share them in the comments below. Great suggestions
sooner or later will turn into a video to make more people aware of that good stuff.
Huge thanks to everyone who supports my work on Patreon and YouTube.
Well, that is all from me and I will see you next time.
Voir Plus de Vidéos Connexes
Bambu P1S vs X1C - Which 3D Printer Is The Best?
The secret to 3D printing PETG [Adventurer 4]
Instant IDでLoRAが不要になる?【Stable Diffusion WebUIでInstant IDを使い同じ顔の人物を生成する方法】
消化に関係する臓器の位置やはたらきを調べるワークシート
【RSR】RADEONの新機能!RADEON Super Resolutionを検証解説!NVIDIA Image Scalingと比べて違いはあるのか?RX 6600 XTで検証
Microsoft Create: Create a podcast worksheet for the classroom using Designer
5.0 / 5 (0 votes)