Remeha Elga Ace - plaatsing & installatie (volledige instructievideo)
Summary
TLDRThis comprehensive video script provides detailed instructions for the installation of an outdoor unit and an indoor unit (LK IS) for a heating system. It covers crucial aspects such as selecting suitable locations, maintaining proper distances from walls, ensuring proper condensation drainage, and implementing vibration dampeners. The script guides through the electrical connections, including power cables, connections between indoor and outdoor units, and thermostats. Additionally, it explains the refrigerant line setup, hydraulic connections, flushing the system, and integrating the indoor unit with the boiler. The script emphasizes crucial steps like positioning filters, cable routing, and parameterization, ensuring a seamless and efficient installation process.
Takeaways
- 🏡 The outdoor unit must be placed in a suitable location, maintaining the minimum distance from walls as specified in the installation manual.
- 💧 Ensure proper drainage for the condensation water from the outdoor unit, e.g., by placing it above a gravel bed.
- 🔊 Use appropriate vibration dampers during installation to prevent noise pollution.
- ⚡ Follow the correct sequence for electrical connections: power cable, work switch, connection between indoor and outdoor units (using only four connectors), and outdoor sensor placement.
- 🔩 Properly solder or crimp the refrigerant line couplings before connecting them to the outdoor unit.
- 📍 Choose a suitable location for the indoor unit (close to the boiler), considering hydraulic connections and access for maintenance.
- 🔧 Mount the indoor unit by first securing the back plate to the wall, then hanging the unit on the plate.
- 🚰 Connect the refrigerant lines to the indoor unit, ensuring proper sealing with gaskets.
- 💨 Evacuate the refrigerant circuit after connecting the lines, following the commissioning video instructions.
- 🔌 Connect the indoor unit to the outdoor unit, boiler, thermostat, and power supply, following the correct wiring sequence and using cable binders for tidy cable management.
Q & A
What is the importance of proper placement of the outdoor unit?
-The outdoor unit must be placed in a suitable location, considering the minimum distance required from walls as specified in the installation manual. This ensures proper airflow and prevents obstructions.
How should the condensation water from the outdoor unit be handled?
-The condensation water from the outdoor unit should not be allowed to accumulate on the ground. It is recommended to place the unit above a gravel bed or other drainage solution to ensure proper drainage of the condensation water.
Why is it important to use vibration dampers during installation?
-Vibration dampers should be used during installation to prevent noise pollution and minimize disturbance caused by the operation of the outdoor unit.
What are the steps involved in making electrical connections for the outdoor unit?
-First, the power cable is run, and the work switch is mounted. Next, the electrical connection between the indoor unit (LK) and the outdoor unit is made, using only four connectors (the two left connectors are not connected). Finally, the outdoor temperature sensor is connected to the LK.
What should be considered when selecting the location for the indoor unit (LK)?
-When choosing the location for the indoor unit (LK), attention should be paid to the proximity to the boiler and the hydraulic connections, ensuring proper placement and accessibility.
What is the purpose of the blind caps on the LK, and what should be checked?
-The blind caps on the LK should be removed, and it should be checked if the system is properly sealed, ensuring no leaks.
Why is it recommended to install a dirt filter during the hydraulic connections?
-A dirt filter should be installed during the hydraulic connections to prevent any dirt or debris from the central heating system from entering the LK, ensuring proper functioning and preventing potential damage.
What are the steps involved in making electrical connections between the LK and the outdoor unit?
-First, the power cable is connected to the LK. Then, the LK and the central heating boiler are connected via the OpenTherm connector. The outdoor temperature sensor is connected to the Temp connector, and finally, the thermostat is connected to the LK via the EIB connector.
What should be done if a new thermostat needs to be installed?
-If a new thermostat needs to be installed, it should be done during the electrical connections phase, following the same procedure of connecting it to the LK via the EIB connector.
Where can additional information about the parameterization and commissioning of the LK be found?
-The script mentions that additional videos covering the parameterization and commissioning of the LK should be consulted for more detailed information.
Outlines
🏘️ Outdoor Unit Placement and Connections
This paragraph discusses the proper placement of the outdoor unit, ensuring appropriate distance from walls and adequate drainage for condensation water. It also covers installing vibration dampers, making electrical connections (power cable, work switch, and connection to the indoor unit), and installing the outdoor temperature sensor. Furthermore, it explains the process of laying refrigerant lines between the outdoor unit and the indoor unit, soldering or crimping the appropriate fittings, and connecting the lines to the outdoor unit.
🏠 Indoor Unit Installation and Connections
This paragraph covers the installation of the indoor unit (LK ES) near the boiler, considering the appropriate location and hydraulic connections. It guides through removing the back plate, marking the position for mounting holes, drilling and securing the back plate to the wall. It then explains hanging the indoor unit on the back plate, removing blind plugs, making refrigerant connections with gaskets, and pressure testing the refrigerant circuit. Additionally, it describes draining the heating system, making hydraulic connections between the boiler and the indoor unit with a dirt filter, and making electrical connections between the indoor unit and outdoor unit, including power supply, connection to the boiler, outdoor temperature sensor, and thermostat.
Mindmap
Keywords
💡Outdoor unit
💡Indoor unit
💡Refrigerant lines
💡Electrical connections
💡Hydraulic connections
💡Condensate drainage
💡Vibration dampers
💡Vacuum testing
💡Thermostat
💡Commissioning
Highlights
The outdoor unit must always be placed in a suitable location with sufficient distance from walls, as specified in the installation manual.
Ensure that the condensation water from the outdoor unit does not accumulate on the ground beneath it, for example, by placing the unit above a gravel bed.
Use suitable vibration dampers during installation to prevent noise nuisance.
Start with the electrical connections by laying the power cable and mounting the work switch.
Make the electrical connection between the indoor unit and the outdoor unit, using only four connections (the two left connectors are not connected).
Place the outdoor sensor in an ideal location, as described in the documentation.
Lay the refrigerant pipes between the outdoor unit and the indoor unit, solder or crimp the fittings, and connect them to the outdoor unit.
The indoor unit should be placed near the boiler, considering the hydraulic connections.
Remove the rear plate, use it as a template to mark the holes, drill the holes, insert plugs, and screw the rear plate to the wall.
Hang the indoor unit on the rear plate and secure it.
Remove the blind caps from the indoor unit, check for tightness, make the refrigerant connections with gaskets, and vacuum the refrigerant circuit.
Drain the heating system by removing the heat demand via the thermostat.
Make the hydraulic connections between the boiler and the indoor unit, including a dirt filter.
Connect the power cable to the indoor unit, then connect the indoor unit to the boiler by removing the thermostat connection and connecting the indoor unit to the same bus connector.
Connect the outdoor sensor to the temp connector, the thermostat to the BUS connector (replace if necessary), and refer to other videos for parameterization and commissioning of the indoor unit.
Transcripts
de buitenunit moet altijd geplaatst
worden op een geschikte locatie
maar wat is nu een geschikte locatie
iedere buitenunit heeft een gewenste
minimum afstand tot een muur zorg ervoor
dat deze afstand altijd aanwezig is
wanneer de unit plaatst in de
installatie handleiding vind je een
helder overzicht van deze afstanden
het condenswater van de buitenunit mag
niet op de grond onder de unit blijven
liggen
zorg er daarom voor dat de buitenunit zo
geplaatst wordt dat het condenswater
direct afgevoerd wordt
bijvoorbeeld door de unit boven hun
grind bed te plaatsen
gebruik bij de plaatsing ook altijd
geschikte trillingsdempers om
geluidsoverlast te voorkomen
nadat de buitenunit is geplaatst kan
worden gestart met de elektrische
aansluitingen
als eerste wordt de voedingskabel
getrokken en wordt de werk schakelaar
gemonteerd
vervolgens wordt de elektrische
aansluiting tussen de lk sn de
buitenunit gemaakt
let op hierbij worden slechts vier
connecties gebruikt de twee linker
connectoren worden niet aangesloten als
laatste plaats je de buitenvoeler
deze sluit je later op de l ga eens aan
bekijk de ideale locatie voor de
plaatsing van de buitenvoeler in de
documentatie
nu worden de koudemiddel leidingen
tussen de buitenunit en de lk is
aangelegd
nadat de juiste koppelingen aan de
koudemiddel leidingen zijn gesoldeerd of
gekrompen
kun je de leidingen op de buitenunit
aansluiten
zodra alle aansluitingen aan de
buitenunit zijn afgerond ga je verder
met de binnenunit
de lk eis wordt altijd in de buurt van
de ketel geplaatst
let bij het kiezen van de geschikte
locatie ook goed op de hydraulische
aansluitingen
om de lk is op te hangen verwijder je
eerst de achterplaat
gebruik deze plaat a small om de positie
van de gaten af te tekenen op de want
waar het toestel opgehangen wordt nu
kunnen de gaten geboord worden
voorzie deze daarna van pluggen en
schroef de achterplaat vast aan de muur
[Muziek]
de lk eis kan nu worden opgehangen en
bevestigd aan de achterplaat
verwijderen als eerste de blind doppen
van de helga is controleer daarmee of
het systeem dicht zit
vervolgens maak je de koudum in alle
aansluitingen aan de helga is
vergeet daarbij niet de pakking tussen
de elga is en de koudemiddel leiding te
plaatsen
zodra de koudemiddel leidingen zijn
aangesloten kun je om efficiënt te
werken vast het koudemiddel circuit
afpersen
bekijk hiervoor ook de video in
bedrijfstelling vervolgens wordt het
cv-systeem afgetapt neem hiervoor eerst
de warmtevraag weg van het systeem via
de thermostaat
nu kan het cv-systeem worden afgetapt
nadat het cv-systeem leeg is kan worden
gestart met het maken van de
hydraulische verbindingen tussen de
ketel en de elkaar eens
vergeet daarbij ook niet om een vuil
filter te plaatsen
dit voorkomt uiteraard dat er vuil
vanuit het cv-systeem in de elkaar komt
nadat het vuil filter is geplaatst
kunnen de kranen worden open gedraaid
nu alle hydraulische aansluitingen zijn
gemaakt kan er gestart worden met het
maken van de elektrische aansluitingen
tussen de elga race en de buitenunit
als eerste wordt de voedingskabel
aangesloten op de elga is zodra alle
werkzaamheden zijn afgerond wordt deze
van spanning voorzien
vervolgens worden de lk sn de cv-ketel
op elkaar aangesloten
verwijder hiervoor eerst de aansluiting
van de thermostaat op de cv-ketel
op dezelfde er bus connector waar eerste
thermostaat zat
wordt nu de connectie met de l ga eens
gemaakt
[Muziek]
leid de kabels worden elga via de
kabelbinders die aan de binnenzijde zijn
geplaatst
dit zorgt voor een goede en
storingsvrije kabelloop de aansluiting
voor de cv-ketel wordt bij voorkeur op
de l ga eens gemaakt via de open term
conrector
de buitenvoeler wordt aangesloten op de
tempo conectar
als laatste wordt de thermostaat
aangesloten op de elga race gebruik
hiervoor ongeacht het type thermostaat
de er bus connector
indien er een nieuwe thermostaat
geplaatst moet worden is dit ook het
moment om dat te doen
bekijk ook de andere video's over de
parametrisering en inbedrijfstelling van
de lk eis
تصفح المزيد من مقاطع الفيديو ذات الصلة
Heating and Cooling VRF System
National Electrical Code: Unit 4
Memelihara dan Memperbaiki Instalasi Listrik Bangunan Gedung - Teknik Instalasi Tenaga Listrik
Fitting Anti Lock Brakes ABS to a non-ABS Motorbike - can it be done ?
SAP INSTALLATION Using SWPM TOOL
X-Pert Studio Build-a-Pole Installation Video
5.0 / 5 (0 votes)