Armadio a muro fai da te con ante IKEA pax
Summary
TLDRIn this DIY video, the creator demonstrates how to build a custom wall-mounted wardrobe using three IKEA doors. They start by measuring the space and using a laser measure for precision, then design the project in Fusion 360. The process involves cutting the doors to fit, using steel plates for hinges, and painting with a durable, scratch-resistant paint from Leroy Merlin. The assembly includes attaching wooden frames and shelves, ensuring a perfect fit with a laser level. The final step is sealing gaps with acrylic silicone for a seamless finish.
Takeaways
- 📏 The video demonstrates how to measure a wall space accurately using a laser measurer to ensure the walls are square and to determine the dimensions for the custom wardrobe project.
- 🛠️ The creator used Autodesk's Fusion 360 software to design the wardrobe, but notes that a simple school ruler and paper could also be used for the design.
- 📐 The main measurements considered were the combined width of two IKEA doors and the height, which needed to cover a space of about 1 meter and 4 centimeters, respectively.
- 🪵 The decision on the width of wooden slats was based on the remaining space after accounting for the wall thickness and the door's coverage.
- 🔪 The long wooden slat was planned to be cut into two parts for easier transportation, with the cut made at the central batten to hide the cut when assembled.
- 🚪 The upper doors were derived from a single door cut in half using an alternative saw and then measured and cut to fit at a Bricofae for a total of 3 euros.
- 🔄 To restore the finish of the upper edge of the door after cutting, edge banding rolls were used, which were then heated and applied to the door with an iron.
- 🔩 The video describes creating a housing for the hinge by using a special drill bit called a Forstner bit, ensuring the depth matches the IKEA panel and stopping in time to avoid marks.
- 🛠️ The creator used a level to ensure the alignment of the hinge holes and used a square to maintain a 90-degree angle for the hinge installation.
- 🎨 After assembling the wooden frame, the creator chose a specific paint from Leroy Merlin designed for wood, which is also suitable for environments with strict hygiene standards like restaurants and kitchens.
- 🔨 The final assembly involved attaching the wooden frame to the wall using specific wood screws, ensuring a secure fit, and then connecting the three crossbars with steel-zinc plates.
- 📐 The use of a laser level was crucial for aligning the shelves and supports to ensure they were perfectly horizontal and vertical.
Q & A
What is the main purpose of the video?
-The main purpose of the video is to explain how to assemble three IKEA doors to create a wall-mounted wardrobe.
What tool did the creator use to measure the wall cavity?
-The creator used a laser measurer to ensure greater precision in measuring the wall cavity.
What software did the creator mention for designing the project?
-The creator mentioned using Autodesk's Fusion 360 software for designing the project.
What is the total width of the two doors combined in the project?
-The combined width of the two doors is 49.5 centimeters, which is approximately 1 meter.
How did the creator address the issue of transporting the long wooden slat?
-The creator planned to split the long wooden slat into two parts to make it easier to transport in a car.
What was the process for creating the top part of the door?
-The top part of the door was created by cutting a single door in half, using an alternative saw, and then cutting it to size at a Bricofèr for 3 euros per cut.
Why did the creator use a special bit called 'bonta forstner'?
-The 'bonta forstner' bit was used to create a circular housing for the hinge on the wooden panel, ensuring a precise fit for the hinge.
What type of paint did the creator use for the doors?
-The creator used a specific paint for wood from Leroy Merlin, which is designed to be both decorative and resistant to scratches and impacts, suitable for environments like restaurants and kitchens with HACCP standards.
How did the creator attach the wooden slats to the wall?
-The creator attached the wooden slats to the wall using specific wood screws and a laser level to ensure a secure and straight fit.
What material was used to fill the gaps between the frame and the wall?
-A special acrylic silicone was used to fill the gaps between the frame and the wall for a clean and hygienic finish.
How were the shelves and supports for the shelves created?
-The shelves and supports were created using wooden slats fixed to the wall with screws, ensuring proper depth and spacing for the shelves to fit snugly.
Outlines
🛠️ Custom Wall Wardrobe Assembly
The video begins with the creator explaining how they assembled a wall wardrobe using four IKEA doors. They first measured the wall to ensure the wardrobe would fit, using a laser measure for precision. The creator used a design program, Autodesk Fusion 360, to plan the project, although it's noted that a simple school ruler and paper could suffice. The main focus was on the width of the two doors together, which needed to cover approximately one meter, with some leftover centimeters to account for the wall's thickness and the door's overlay. The top and bottom lengths were also considered, with the top piece being split into two for easier transportation. The video includes a music and applause segment to engage the audience.
🔨 DIY Door Restoration and Hinge Installation
In the second paragraph, the focus shifts to restoring the upper edge of the door, which had lost its finish during the cutting process. The creator uses a meranti veneer roll, a type of wood layer, applied with a Casey Shaw adhesive iron to recreate the door's edge. After attaching the veneer, it's carefully trimmed to match the door's shape. The video then moves on to creating a housing for the hinge. The creator uses a Forstner bit, a woodworking tool, to carve a circular housing in the wood panel, ensuring it matches the depth of an IKEA door panel where the hinge will be attached. The process involves testing the fit of the hinge and marking the screw holes for alignment. The door is then painted with a specific paint for wood from Leroy Merlin, suitable for kitchens and restaurants, making it resistant to scratches and wear.
🏠 Wall Mounting and Shelves Construction
The final paragraph details the assembly of the custom wardrobe. The creator attaches wooden battens to the wall, ensuring the measurements are accurate and using wall plugs for secure attachment. The doors are then mounted using specific wood screws. A level laser is used to ensure the framework is perfectly vertical. The creator also discusses the construction of shelves, using wooden battens fixed to the wall with screws, and the importance of leaving space for the shelf edge to fit snugly. The gaps between the framework and the wall are filled with acrylic silicone for a seamless finish. The video concludes with a reminder to ask questions in the comments and to stay tuned for more content.
Mindmap
Keywords
💡IKEA doors
💡Laser measure
💡Fusion 360
💡Wooden slats
💡Cutting
💡Bricofer
💡Meranti veneer
💡Forstner bit
💡Hinges
💡Assembly
💡Sanding and painting
💡Silicone sealant
Highlights
The video demonstrates how to assemble three IKEA doors to create a wall-mounted wardrobe.
The process begins with measuring the width and height of the space to ensure the walls are square.
A laser measure is used for increased precision in taking measurements.
Fusion 360 by Autodesk is mentioned as the software used for the project design, though it's not mandatory for such a project.
The total width to be covered by the two doors is measured to be 49.5 centimeters.
The leftover width of 4 centimeters is considered for the wood slat width.
The height of the wood slat is planned to be split into two parts for easier transportation.
Upper doors are derived from a single door cut in half using an alternative saw and then measured at a hardware store.
The edges of the cut doors are finished with a veneer to restore the appearance.
A special bit called a Forstner bit is used to create circular housings for the hinges.
The depth of the wood panel is measured to match the hinge thickness of approximately 12-13 mm.
A trial is conducted on a spare panel to ensure the proper alignment of the hinge holes.
The IKEA panel is used to create a custom door with a single panel.
The door is painted with a specific paint for wood from Leroy Merlin, suitable for kitchens and restaurants.
The paint is chosen for its resistance to scratches and abrasions, complying with HACCP standards.
After painting, the wood slats are assembled to form the frame, ensuring proper measurements.
Wall holes are drilled for mounting the frame securely with specific wood screws.
A leveling laser is used to ensure the frame is perfectly aligned with the wall during assembly.
Shelves and supports are created following the guidelines of the leveling laser for precision.
Wood slats are fixed to the wall to create supports for the shelves with an exact depth.
The shelves are adjusted to fit perfectly, leaving a small gap for the shelf edge.
Any gaps between the frame and the wall are filled with acrylic silicone for a seamless finish.
Transcripts
ciao a tutti in questo video cerco di
spiegarmi come ho montato quattro ante
anzi tre anche ikea per realizzare un
armadio a muro
[Musica]
[Applauso]
[Musica]
innanzi tutto quello che ho fatto è
stato quello di prendere le misure del
vano che volevo andare a coprire quindi
larghezza x altezza in diversi punti in
modo tale da verificare
più o meno se le pareti erano a squadre
per fare questo mi sono basso di un
misuratore laser in modo tale da avere
una precisione maggiore le misure poi le
oggi impiegate per realizzare il
progetto vero e proprio su carta nel mio
caso particolare ho usato un programma
che si chiama fusion 360 di autodesk ma
voglio dire non è necessario arrivare al
programma chiunque di voi può realizzare
un progetto anche con carta in mattina a
scuola tra le ringhiere allora quello
che ho considerato in particolare è la
larghezza che mi andava a coprire le due
ante messe insieme un'altra misura
49,5 centimetri quindi insieme
andrebbero a coprire una luce di
un metro circa nel mio caso avendo una
pezza da parete apparese di 108 cm mi
restano scoperti grosso modo 4 cm per
lato questa misura poi mi servirà per
decidere che larghezza di listelli di
legno
vado a prendere nella larghezza
dell'esterno ho considerato quindi i
quattro centimetri che mi rimanevano
aperti
da alta a parete ma anche
la misura che in copre anni va a coprire
l'alta la larghezza dell'altra cioè 1,8
cm e quindi la larghezza totale sarà di
4 centimetri nel mio caso più 1,8 cm che
è quella che va a coprire latta
l'altezza da 2 metri e 70 e diciamo un
problema per trasportare poi in macchina
il listello quindi nel progetto o
previsto la separazione di questo
mistero in due parti l'ho fatto tagliare
al punto in cui combacia con il battente
centrale
io in questo caso lo stoccato quindi non
si vede più il taglio in questo modo
potremo portare facilmente
il listello nella nostra auto perché
avremo due listelli uno da circa due
mesi e un altro di circa 70 centimetri
che tranquillamente potremmo trasportare
in macchina le ante superiori le anche
superiori derivano da un'unica anta
forza tagliata a metà prima tagliata a
metà da da meta attraverso un seghetto
alternativo e poi fatta tagliare su
misura da
a un centro bricofer dove con 3 euro al
taglio quindi se euro totali mi sono
andato a ricavare le due ante superiori
perfettamente al quadro
[Musica]
allora una volta tagliate dalla centro
bricofer comunque rimaneva il l'unico
difetto che abbiamo tolto la rifinitura
del bordo superiore e quindi per
ripristinare questo bordo vengono
venduti affonda appositamente dei rotoli
di merani nico cioè di utile strato di
legno che con un via adesivo casey shaw
l'idea con il il calore poi si applica
sulla sul fondo con un ferro da stiro
una volta quindi incollato la rifinitura
ho proceduto a toglierla con un
taglierino
tagliandola in questo modo e quindi
abbiamo la nostra anta fatta su misura
ma non ancora completa perché
tagliandola a metà poi ci manca la parte
superiore dell'alloggiamento della
cerniera e quindi per creare questo
alloggiamento uno lo abbiamo conservato
ma ci manca quello più in alto per
questo alloggiamento ho preso ovviamente
le misure esatte simmetriche quindi
rispetto a quella della base ho potuto
procedere a creare questo alloggiamento
che si realizza attraverso una punta
speciale per travano che si chiama bontà
forstner questa punta si scava diciamo
in maniera circolare il pannello di
legno ho preso la misura della
profondità che ha un pannello ikea in
questo punto doveva associarsi alla
cerniera che circa 12 13 mm importante è
fermarsi in tempo per non creare un
segno una parte opposta
per questo in ogni momento ho cercato
sempre di fare una prova sul pezzo
centrale dell'alta che mi era valsa
anche per creare la rifinitura della
bordo lo ha prima provato che su questo
pannello che mi era avanzato
l'individuazione dei fori che vanno ad
ospitare le viti della cerniera
mi sono regolato alloggiando la cerniera
e
mettendo la squadra con la squadra per
legno proprio da falegname in questo
caso ci dà la perfetta di linearità a 90
gradi della cerniera e quindi poi non
avremo problemi di tendenze
qui una volta che mi sono creato la mia
bella anta su misura è sempre fatta con
un solo pannello di ikea ho potuto
procedere alla loro loro montaggio
dopo questo passaggio ho proceduto
naturalmente a proteggere isterie a
dargli anche la tinta quindi ho scelto
una tinta che
facesse entrambe le tue cose dopo circa
anche due mani il risultato era ottimo è
una tinta che ho preso ti da leroy
merlin specifica per legno all'interno
ho dato una vernice a smalto specificati
era situazioni diciamo di ristoranti di
cucine si formerà normativa haccp
in questo modo rende molto resistente la
parte interna quindi graffi urti non non
creeranno delle abrasioni sulla parete
dopo aver tinteggiato ho proceduto ad
assemblare i listelli di legno quindi la
cornice lo
assemblata e ho verificato le misure se
andassero bene ho realizzato dei fori
sulla parete dove promesso dei tasselli
in modo tale da vincolare saldamente i
due montati cioè i 4 contanti in
definitiva alla parete tramite delle
viti specifiche per legno in questo caso
ho
inserito due
viti che reggono questa prima parte di
montanti e altre due viti in alto che
reggono la seconda parte del montante la
cerniera mi va a finire proprio al
centro e quindi questo punto non ho
potuto mettere una terza vite in questa
fase o anche diciamo provveduto a far
sparire la il punto in cui si vedeva
magari il taglio del del montante e
quindi stoccando attraverso uno stucco
specifico per legno che ho trovato
sempre dalle rom marley che carte giando
e quindi verniciando sempre con la
stessa vernice o raggiunto questo
risultato e premete è impossibile vedere
questo tanto una volta assemblato ho
collegato se le tre traverse con del
lt delle placche in acciaio zincato
sopra è alla base
quindi una volta che mi sono creato la
mia bella anta su misura è sempre fatta
con un solo pannello di ikea ho potuto
procedere alla loro loro montaggio che è
stato molto semplice quanto dovuto
creare soltanto gli inviti per le viti
del della cerniera come li ho creati o
affiancato l'anta
completamente chiusa attaccata al
montante
in questo modo poi ho preso dall'interno
i punti dove andavano fatti i pre fori e
quindi una volta fatti preposti non è
restato altro da fare che avvitare le
cerniere i punti in cui può vincolato
cerniere al telaio e diciamo davano
riscontro del progetto
nella pa di misurazione è stata
utilissima anche dopo questa a livella
al laser in questo caso noi abbiamo il
montaggio perfetto a piombo del del
telaio mi è stata utilissima anche nella
fase di creazione degli scaffali e per
il più precisamente degli appoggi dove
ha proprio il corato i ripiani sono
stati realizzati seguendo le linee guida
di questa livella notare che poi avremo
lo scaffale perfettamente in bolla gli
appoggi per gli scaffali sono stati
realizzati con dei listelli di legno
fissati alla parete con due tasselli sui
lati corti e tre tasselli sui sui lati
lunghi i ripiani fissati dall ero amarle
infatti se gare su misura tenendo conto
della profondità e tenendo conto di
lasciare almeno un centimetro scarso di
distanza tra il bordo del ripiano per la
santa e poi per sfruttare tutta la
profondità o
segato su misura che gli angoli del dei
ripiani in questo modo andava ad avere
altri circa
45 centimetri di profondità per finire
ho riempito
le fessure erano rimaste tra il telaio e
la parete con un silicone speciale un
silicone acrilico che va a riempire
proprio le fessure tra le pareti questo
silicone l'ho dato su tutti i bordi del
terraglio compreso la la la traversa a
terra e la traversa superiore abbiamo
eliminato ogni fessura anche per diciamo
ragioni igieniche mi sembra di aver
detto tutto se avete ulteriori domande
che potete chiedere nei commenti di
questo video e naturalmente scrivetevi
così non vi perderete i prossimi
[Musica]
[Musica]
Просмотреть больше связанных видео
![](https://i.ytimg.com/vi/sl9vZ-q3bkQ/hq720.jpg)
Come nasce il DAILY? Tutti i segreti della MEGA fabbrica IVECO 🇮🇹
![](https://i.ytimg.com/vi/jSoKT2Bvs-Q/hq720.jpg)
Möbel bauen im VW T6 Adventure Van! Küche und jede Menge Stauraum!
![](https://i.ytimg.com/vi/9xOI7pl5pkQ/hqdefault.jpg?sqp=-oaymwEXCJADEOABSFryq4qpAwkIARUAAIhCGAE=&rs=AOn4CLBFOHQ8JdzOTDmPZ17qzKOsS-u4Gg)
Fusion 360 beginner's Exercise #9 - Fusion 360 tutorial
![](https://i.ytimg.com/vi/tW_DhdDZeKM/hq720.jpg)
Créer un organigramme sur Word
![](https://i.ytimg.com/vi/BOObMx8QQOM/hq720.jpg)
Costruisco un proiettore LASER e proietto Nonno LASER - @SurvivalHacking @PierAisa @Kaoslaleggenda
![](https://i.ytimg.com/vi/dMpoXyeSa0o/hqdefault.jpg?sqp=-oaymwEXCJADEOABSFryq4qpAwkIARUAAIhCGAE=&rs=AOn4CLCV-NVe6e2_Pk2JyZOE0y9udwN6Qw)
Fusion 360 beginner's Exercise #7 - Fusion 360 tutorial
5.0 / 5 (0 votes)