👉 Sony Bravia Led rojo enciende 6 veces [RESUELTO💯] Problema de parpadeo Electronica Nuñez👉❤️
Summary
TLDRIn this video, the presenter demonstrates troubleshooting a common issue with a Sony Bravia TV, where it fails to stay on due to backlight problems. After identifying that the TV enters protection mode due to LED backlight failures, the presenter uses an oscilloscope to diagnose the problem. They provide step-by-step instructions on how to bypass the TV's protection mechanism using a resistor to ground the control pin. This method allows the TV to function without disassembling the screen further. The video concludes with confirming that the LEDs are working correctly, restoring full functionality.
Takeaways
- 🔌 The video demonstrates how to troubleshoot a common issue with a Sony Bravia TV that enters protection mode.
- 🔴 When powered on, the TV shows the Sony logo briefly, then turns off and flashes red in standby mode, indicating a backlight protection issue.
- 🔦 The problem likely lies with the backlight controller or one of the LED strips, but it is not necessary to disassemble the TV fully to resolve the issue.
- 📏 The creator uses an oscilloscope to check the return pulses from the LED strips, setting it to 2 volts per division and 500 microseconds.
- 📊 By measuring the return voltages from the three LED strips, the technician confirms that each returns a consistent 4 volts, ruling out damaged LED strips.
- 💡 The next step is to analyze the signals from the backlight controller, specifically checking the error detection and pulse communication.
- 🔧 The technician targets pin 31 on the controller IC, associated with the error line, to monitor the pulse response using the oscilloscope.
- ⚡ The problem is resolved by connecting a 10,000-ohm resistor between pin 31 and ground, eliminating the error pulse and enabling the backlight to stay on.
- 📺 After the repair, the backlight functions correctly, and there are no signs of faulty LEDs or dark spots on the screen.
- ✅ The video concludes with the technician verifying the TV works properly by connecting an HDMI source, showing that the screen displays as expected without further issues.
Q & A
What is the common issue being addressed in the video?
-The video addresses a common issue with Sony Bravia screens where the backlight fails, causing the TV to enter protection mode and display a green color, followed by red standby light indicating the problem.
What does the green color on the screen indicate?
-The green color on the screen indicates that the divider has been turned on and the TV is starting up.
What does the red standby light signify?
-The red standby light signifies that the TV has entered protection mode, indicating a problem with the backlight.
What could be the possible causes of the backlight failure?
-The possible causes of the backlight failure could be a faulty backlight controller, damaged LEDs, or a specific LED that is not functioning properly.
What is the purpose of eliminating the protection mode in the tutorial?
-Eliminating the protection mode is intended to force the TV to turn on the LEDs, which might still be in good condition, thereby giving the TV some utility without needing to disassemble it further.
What is the first step the presenter takes to diagnose the issue?
-The first step the presenter takes is to disassemble the TV and locate the backlight controller to diagnose the issue.
Why does the presenter suggest that disassembling the screen might not be necessary?
-The presenter suggests that disassembling the screen might not be necessary because sometimes the issue is with just one LED, and the rest of the LEDs might still function correctly.
What diagnostic test does the presenter perform to check the LED strips?
-The presenter performs a diagnostic test using an oscilloscope to check the return pulse from each LED strip to determine if any are damaged.
What do the three flashes on the screen typically indicate?
-Typically, three flashes on the screen indicate that there is a problem with the TV's backlight, and it is entering protection mode.
What does the presenter conclude after checking the return pulse from the LED strips?
-After checking the return pulse, the presenter concludes that the failure is not due to damaged LED strips since all three reference points of return voltage are showing 4 volts each.
How does the presenter determine the functioning of the backlight controller?
-The presenter determines the functioning of the backlight controller by observing the signals on the data points of the integrated circuit, specifically looking at the clk, error, cp, pwm, and ddm signals.
What is the significance of the line CP in the context of the video?
-The line CP is significant because it can indicate problems with the integrated circuit if there is an error in frequency or signal level, leading to the TV entering protection mode.
What is the solution the presenter applies to resolve the issue?
-The presenter resolves the issue by connecting a resistor between pin 31 of the controller and the negative ground (chassis) to bypass the error signal.
How does the presenter verify that the LEDs are functioning correctly after applying the solution?
-The presenter verifies that the LEDs are functioning correctly by checking for uniform lighting and connecting an HDMI signal to display a white screen, ensuring there are no dark spots or shadows indicating damaged LEDs.
Outlines
🔌 Introduction to Common Sony Bravia TV Issue
The video begins with an introduction to a common issue faced by Sony Bravia TVs, where the TV enters protection mode due to backlight failure. The presenter connects the TV to power and observes that the Sony logo appears briefly before the screen goes black, followed by red standby light flashes. This indicates that the backlight is malfunctioning. The issue may be related to the backlight controller or specific LED strips. The presenter explains that the video will demonstrate how to bypass this protection mode to get the TV functioning without extensive repairs.
🔍 Diagnosing Backlight Controller and LED Strips
The presenter disassembles the TV to investigate the backlight controller, explaining that the problem is often caused by damaged LED strips. However, instead of disassembling further, the presenter opts to test the return signals from the LED strips using an oscilloscope. They explain the setup: adjusting the oscilloscope to 2 volts per division and 500 microseconds per division to measure the pulses. The test reveals a consistent 4-volt pulse return from all three LED strips, indicating that the LEDs themselves are not faulty. This rules out LED strip damage as the cause of the problem.
📊 Investigating the Backlight Controller Chip
The presenter shifts focus to the backlight controller chip, specifically a 9327 model. They explain the role of key signals, such as the return pulse, clock, and error lines. The return pulse tests indicate no issue, so the error lies in another signal. The error signal, triggered by the controller chip, is responsible for the protection mode. The presenter measures the error pulse at pin 31 of the chip, adjusting the oscilloscope to 1 volt per division. The test reveals a 2-volt pulse, confirming the error line is causing the TV to enter protection mode.
⚡ Bypassing the Error Signal to Restore Function
To resolve the issue, the presenter demonstrates how to bypass the error signal by grounding pin 31 of the controller chip using a 10,000-ohm resistor. After connecting the resistor between pin 31 and the chassis ground, they power on the TV and observe that the backlight LEDs illuminate correctly without the previous 2-volt error pulse. The TV successfully bypasses the protection mode, and the LEDs remain on.
📺 Testing TV Display for LED and Image Quality
The presenter tests the TV display by connecting an HDMI signal and displaying a white screen. This ensures that all LEDs are functioning properly and there are no dark spots or shadows, which would indicate damaged LEDs. The white screen displays evenly, confirming that all LEDs are working. The presenter concludes by noting that the simple bypass technique successfully resolved the issue with the Sony Bravia TV, without needing to replace any LED strips or perform more invasive repairs.
Mindmap
Keywords
💡Backlight
💡Protection mode
💡LED reglets
💡Oscilloscope
💡Return pulse
💡Integrated controller
💡Pin 31
💡Error pulse
💡Resistor
💡HDMI signal
Highlights
Introduction of the issue with a Sony Bravia screen, experiencing one of the most common failures.
Description of how the TV enters protection mode, as indicated by red flashes in the standby light.
Identification of the issue in the backlight system, potentially caused by the backlight controller or a faulty LED.
The goal of the tutorial is to bypass the protection and use the TV without full disassembly.
The presenter disassembles the TV to access the backlight controller and performs a diagnosis of the LED strips.
Explanation of using an oscilloscope to check the return pulses from the LED strips, indicating if the LEDs are functioning correctly.
Demonstration of detecting a 4V return pulse from each LED strip, indicating that the LED strips are working properly.
Conclusion that the issue is not due to damaged LED strips, but may be related to the backlight controller IC.
Discussion of the backlight controller IC’s operation, including how error signals are triggered.
Verification of the error pulse using an oscilloscope, showing that the IC triggers the error signal when an anomaly is detected.
Solution: Grounding pin 31 of the backlight controller IC using a 10,000-ohm resistor to bypass the protection circuit.
Confirmation that the TV successfully powers on with all LEDs functioning properly after bypassing the protection.
Final test: Connecting the TV to an HDMI source to verify that the display works and no LEDs are damaged.
Explanation that any dark spots on the screen would indicate damaged LEDs, but in this case, the screen is fully lit without issues.
Summary: The tutorial successfully bypasses the backlight protection on a Sony Bravia TV, restoring functionality without replacing the LED strips.
Transcripts
hola mis queridos amigos ya estamos de
regreso con otro vídeo más de
electrónica mini tutoriales nuevamente
tenemos acá una pantalla de la marca
sony bravia una pantalla que también
está representando una de las fallas
comunes como siempre voy a conectarlo a
la red eléctrica vamos a presionar la
tecla power para que pueda observar cómo
es la avería ok
muy bien acá como pueden observar ya
tenemos el estaba el color verde lo cual
me está indicando que el divisor tiene
que encender efectivamente el arranca y
tenemos la marca sony pero
inmediatamente se apaga después de esto
vemos alguna serie de destellos en el
stand by color rojo lo cual nos está
indicando que el televisor en este
momento pues ha entrado en protección el
backlight ok significa entonces señores
que la falla que tenemos en este
televisor efectivamente se encuentra en
la zona del backlight podría ser falla
del controlador de backlight o de alguna
realiza leds o de algún led en
específico y lo que nosotros vamos a
hacer en este vídeo tutorial es eliminar
esa protección y con esto el televisor
tendrá que encender las led
el que aún está en buena cabe mencionar
que en algunos casos pues sólo por algún
led de que todo el sistema de retención
pero eliminando esto aún así podemos
darle utilidad al televisor sin
necesidad de desarmarlo y hacer más
trabajos adicionales ok si estás
interesado sobre la información que
hasta el final del vídeo y así vas a
aprender más sobre qué se debe hacer
para buscar resolver problemas en estos
televisores de la nueva generación
entonces señores yo voy a proceder a
desarmarlo y luego continuamos con el
tutorial muy bien amigos como pueden
observar ya lo hemos desarmado y para
buscar resolver este problema
directamente nosotros nos vamos a ubicar
en lo que sería el controlador del
backlight recuerde de que comúnmente
cuando ocurren estos problemas es porque
alguna reale tales se ha dañado pero
muchas veces nos toca desarmar la
pantalla y garage no es tan letal y nos
damos cuenta de que efectivamente todas
las reales se iluminan de manera
correcta entonces para que nosotros no
hagamos trabajos adicionales lo que
debemos de hacer es realizar una serie
de pruebas
es tan sencillas como las que voy a
explicar a continuación para eso voy a
utilizar esta vez ni un sí los copio
mismo
y lo que voy a hacer es verificar el
pulso de retorno proveniente desde cada
una de las regletas para eso entonces yo
voy a ubicar lo que sería o configurar
lo que sería el mismo les copio y vamos
a dejarlo a 2 voltios por división y lo
vamos a ajustar a 500 microsegundos por
división ahora sí vamos a conectar el
televisor a la red eléctrica
y vamos a verificar los pulsos de
retorno recuerde de que acá tenemos
únicamente tres líneas lo que significa
de que este es el retorno de tres
regletas leds y efectivamente pues
llegan a lo que serían este sector aquí
tenemos uno dos tres puntos este serían
estos tres puntos los que nosotros
debemos de monitorear
ahora voy a verificar acá en el primer
punto en este momento cuando nosotros
hicimos la primera prueba al iniciar el
vídeo únicamente pues el tres hornos
reflejó un destello y luego entró en
protección pero comúnmente estos
televisores generan tres destellos y
después de eso nos genera por la
indicación en el stand by de manera
consecutiva lo que comúnmente son seis
veces el flasheo que genera vamos
nosotros a verificar acá el primer punto
de retorno y vamos a presionar la tecla
power
vamos a verificar
muy bien ahí como puede observar tuvimos
un pulso el cual me está marcando que es
de 4 voltios ok
tenemos el osciloscopio a 2 voltios por
división este es el siguiente pulso
vamos a verificar de la misma manera el
resto de los los pines de retorno en
este caso sería este punto que tenemos
acá y en este otro pero en este momento
ya el televisor entro en protección
desconecto espero que termine lo que es
la carga de voltaje que he quedado en
los capacitores electrolítico y se
recete nuevamente el televisor y se
recete
ahora sí voy a verificar en el siguiente
pulso recuerde que si hemos encontrado 4
voltios en el pulso de retorno lo que
sería una regleta sled efectivamente
deberían de ver 4 voltios en cada uno de
los retornos voy a tomar lectura lo que
sería el otro punto y voy a presionar
las teclas power
vamos a esperar que el televisor de
arranque
muy bien ahí generó el otro pulso como
puede observar efectivamente también es
de 4 voltios
ahora vamos a verificar el último
como puedes ver también de la misma
manera
únicamente pues ha marcado 4 voltios lo
que significa de que los tres puntos de
referencia de retorno de voltaje están
marcando efectivamente 4 voltios cada
uno de ellos con esta pequeña prueba
pues nosotros podemos determinar de que
la falla en esta pantalla no se debe a
regletas leds dañadas
entonces ahora lo que nosotros vamos a
hacer es tratar de conocer cómo es el
funcionamiento o cómo es el monitoreo
que genera el integrado controlador del
backlight muy bien amigos entonces
tenemos esta parte de datos del
integrado de 93 27 se ve y tenemos acá
lo que es la secuencia de operación y lo
que sería la activación del error
entonces nosotros podemos observar los
puntos clk punto error el punto cp y el
punto p w
m el punto p doble d m en este momento
nosotros no deberíamos de desconfiar de
él porque él es el que monitorea lo que
es el pulso de retorno proveniente de
las regletas led y la prueba que
acabamos de realizar nos da a conocer de
que el pulso de retorno desde las letras
led pues es correcto significa entonces
de que acá nosotros nos vamos a dudar de
esa señal pero el bm por otro lado
tenemos lo que es la señal clock de la
cual tampoco vamos a dudar porque si
existe una comunicación entre el
microprocesador y el integrado
controlador
y de hecho se está generando el pulso de
activación o de lo contrario no
observaremos que los leds se activan ok
entonces nos queda la línea es la línea
cp en la línea de s&p podemos observar
acá un margen de error de 2 voltios y
esta caída nuevamente para su
estabilidad significa de que si tenemos
problemas con el integrado entonces va a
generar este error de este eleve de
frecuencia o lb de señal a 2 voltios y
luego una caída para estabilizarse
cuando se detecta esta anomalía en el
integrado entonces el circuito error o
la línea error se activa generando nos
la secuencia de los 6 destellos que
conocemos o hemos visto en esta pantalla
entonces señores lo que nosotros vamos a
hacer a continuación es verificar la
línea esp la cual -según el integrado es
la pata número 31 en este caso tenemos
acá que sería exactamente ésta lo que
sería la línea
de la pata número 31 vamos a ubicarnos
directamente a ese sector muy bien
entonces a continuación nos vamos a
ubicar directamente a lo que es la pata
número 31 del integrado controlador y
efectivamente acá tengo el condensador
ahí es donde nosotros vamos a tomar
lecturas para esto entonces vamos a
vamos a ajustar el osciloscopios a un
voltio por división
y siempre lo vamos a dejar a 500
microsegundos por división y así vamos a
poder observar lo que es el pulso de
error del cual hemos mencionado
anteriormente muy bien voy a conectarlo
a la red eléctrica
y voy a ubicarme directamente en lo que
es la línea número 31
ahí estamos correctamente ahora voy a
presionar la tecla power y vamos a
esperar que el televisor arranque
muy bien voy a poner stock ahí como
puede observar efectivamente puedo
verificar el pulso del cual estamos
hablando en la imagen anterior
exactamente de dos volteos
ok
vamos a verificar acá vamos a esperar
que el integrado me entregue lo que
serían los tres pulsos correspondientes
ya lo he desconectado
vamos a conectar nuevamente
todavía está en protección
ahí está todavía en error
vamos a esperar que se recete
ahora si conectamos nuevamente nos
ubicamos en la pata 31
donde se encuentra el condensador vamos
a verificar el osciloscopio
y presionamos la tecla power para
verificar los tres pulsos
correspondientes
ahí está el primero
ay el televisor nuevamente se apagó
ahora voy a tratar de encender
nuevamente nos vamos hasta el siguiente
pulso ahí está
aquí va nuevamente
ahí está el tercero y después de esto el
televisor pues queda en protección
entonces para resolver eso nosotros lo
que tenemos que hacer es tirar a tierra
castilla negativos días y así es esa
línea número 31 con una resistencia
en este caso tengo una resistencia de
10000 omnium ok voy a colocar esa
resistencia de 10.000 o menos entre la
pata 31 y negativo tierra chasis
muy bien ahí como puede observar ya he
colocado la resistencia en su lugar
correspondiente ahora sí lo vamos a
conectar a la red eléctrica
y vamos a tomar lectura algo que sería
siempre pues la pata número 31
voy a ubicar la punta de los hilos
copiosas
y voy a presionar la tecla power
vamos a esperar que el televisor
encienda
y como puedes ver aquí se han iluminado
de manera correcta la regleta led y acá
ya no tengo el pulso de 2 voltios que me
estaba marcando a un principio ok
ahí estamos tocando exactamente la pata
31
no tenemos ese pulso y los leds
efectivamente han quedado encendidos de
manera correcta
ahora vamos a verificar la luminosidad y
me está entregando lo que serían las
letales
dijo
muy bien ahí como puedes observar
efectivamente pues puedo darme cuenta
que todos los leds se han iluminado de
manera correcta ahora voy a colocar la
señal hd e-mail
para verificar la señal de pantalla
blanca
y así poder dar cuenta si efectivamente
había algún led que estuviera pues
dañado o que se note y pues parte que
estemos cura donde me estaría indicando
que tendríamos problemas con algún led
voy a conectarle aca hdmi
ahí está elemental
muy bien ahí tengo pantalla blanca y
efectivamente como puedes darte cuenta
todos los leds se han iluminado de
manera correcta
de no ser así tuviéramos puntos o
sombras negras ahí indican un 2 de que
un sector de esos lugares pues hay
diodos leds dañado pero hoy
efectivamente todos los leds se han
iluminado de manera correcta entonces
señores como pueden darse cuenta
con esta técnica muy simple y sencilla
hemos resuelto el problema en esta
pantalla de la marca sony bravia ok
entonces este es otro vídeo más para la
colección de vídeo de electrónica muy
bien tutoriales nos vemos hasta el
siguiente tutorial
Voir Plus de Vidéos Connexes
PAANO AYOSIN ANG SONY BRAVIA NAG PAPATAY SINDI AYAW MAG TULOY NANG BUKAS
Tivi LG43UK6540 bị sáng trắng màn hình, xử lý bằng hai cách
This serious issue was a simple fix... Here's how!
COMO CONECTAR TU CELULAR A CUALQUIER TELEVISOR SIN CABLES!
How to Update AirPods/Airpods Pro Firmware: 3 Ways
Toyota Sequoia Rear Hatch Stuck, can't open
5.0 / 5 (0 votes)